Toshiba Tosvert VF-AS1 - Manual (Page 245)

K-7
E6581301
11
[4] Terminal response time setup
Vector control
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Speed
control
Torque
control
PM
control
V/f Reference
H 0140
Input terminal 1 response time
selection (F)
2~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0141
Input terminal 2 response time
selection (R)
2~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0142
Input terminal 3 response time
selection (ST)
2~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0143
Input terminal 4 response time
selection (RES)
2~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0144
Input terminal 5~12 response
time selection
2~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0145
Input terminal 13~20 response
time selection
5~200ms 1/1 8 Disabled ●/● ●/● ● ● 7. 2. 3
H 0164 Input terminal selection 17(B12) 0~135 *1 1/1 0 Disabled ●/● ●/● ● ● 7. 2. 1
H 0165 Input terminal selection 18(B13) 0~135 *1 1/1 0 Disabled ●/● ●/● ● ● 7. 2. 1
H 0166 Input terminal selection 19(B14) 0~135 *1 1/1 0 Disabled ●/● ●/● ● ● 7. 2. 1
H 0167 Input terminal selection 20(B15) 0~135 *1 1/1 0 Disabled ●/● ●/● ● ● 7. 2. 1
H 0168
Output terminal function
selection 10 (R3)
0~255 *2 1/1 254 Disabled ●/● ●/● ● ● 7. 2. 2
H 0169
Output terminal function
selection 11 (R4)
0~255 *2 1/1 254 Disabled ●/● ●/● ● ● 7. 2. 2
H 0170 Base frequency 2 25.0~HJ Hz 0.1/0.01 *4 Disabled - - ● ● 6. 4. 1
H 0171 Base frequency voltage 2 50~330V/660V 1/0.1 *3 Disabled - - ● ● 6. 4. 1
H 0172 Manual torque boost 2 0.0~30.0% 0.1/0.1 *3 Enabled - - ● ● 6. 4. 1
H 0173
Motor overload protection level
2
10~100% 1/1 100 Enabled - - ● ● 6. 4. 1
H 0174 Base frequency 3 25.0~HJ Hz 0.1/0.01 *4 Disabled - - ● ● 6. 4. 1
H 0175 Base frequency voltage 3 50~330V/660V 1/0.1 *3 Disabled - - ● ● 6. 4. 1
H 0176 Manual torque boost 3 0.0~30.0% 0.1/0.1 *3 Enabled - - ● ● 6. 4. 1
H 0177
Motor overload protection level
3
10~100% 1/1 100 Enabled - - ● ● 6. 4. 1
H 0178 Base frequency 4 25.0~HJ Hz 0.1/0.01 *4 Disabled - - ● ● 6. 4. 1
H 0179 Base frequency voltage 4 50~330V/660V 1/0.1 *3 Disabled - - ● ● 6. 4. 1
H 0180 Manual torque boost 4 0.0~30.0% 0.1/0.1 *3 Enabled - - ● ● 6. 4. 1
H 0181 Motor overload protection level 4 10~100% 1/1 100 Enabled - - ● ● 6. 4. 1
*1: ⇒ For the adjustment range, see the table on page K-41.
*2: ⇒ For the adjustment range, see the table on page K-43.
*3: Default values vary depending on the capacity. ⇒ See the table of K-46.
*4: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)