) setup video processing – Grass Valley Trinix NXT v.3.3.1 User Manual
Page 384
384
Trinix NXT — Installation and Service Manual
Section 11 — Analog Input Processing
| | | | | | +------------- Input Video Gain (%) |
| | | | | | | +----- Enable ACC (On/Off) |
| | | | | | | | |
+---+---+---+---+---+---+-------+--------------------------------------------+--
0, 0, 0, 0, 2, 1, 100.0, 1 525
1, 0, 0, 0, 2, 1, 100.0, 1 N/A
2, 0, 0, 0, 2, 1, 100.0, 1 N/A
3, 0, 0, 0, 2, 1, 100.0, 1 N/A
4, 0, 0, 0, 2, 1, 100.0, 1 N/A
5, 0, 0, 0, 2, 1, 100.0, 1 N/A
6, 0, 0, 0, 2, 1, 100.0, 1 N/A
7, 0, 0, 0, 2, 1, 100.0, 1 N/A
8, 0, 0, 0, 2, 1, 100.0, 1 N/A
9, 0, 0, 0, 2, 1, 100.0, 1 N/A
a, 0, 0, 0, 2, 1, 100.0, 1 N/A
b, 0, 0, 0, 2, 1, 100.0, 1 N/A
c, 0, 0, 0, 2, 1, 100.0, 1 N/A
d, 0, 0, 0, 2, 1, 100.0, 1 N/A
e, 0, 0, 0, 2, 1, 100.0, 1 N/A
f, 0, 0, 0, 2, 1, 100.0, 1 N/A
Press: '0 ~ 9' or 'A ~ F' to select channel to edit.
Press: 'M' to move/copy channel configuration.
Press: 'Z' to set ALL channels to factory defaults.
Press 'ESC' to return to Main Menu.
When an input (channel) is selected, the display will show the values for
that particular channel. For example, selecting “0” will display the values
for channel 0:
Figure 268. Composite video setup menu for one channel (NTSC shown).
Video Composite In -
--------------------------------------------------------------------------------
Reference - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
================================================================================
Selected - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
--------------------------------------------------------------------------------
Disable (Off) 0 Video Decode Mode: Input Video Gain:
Enable (On) 1 No filter 1 50.0 to 200.0% (0.5% steps)
Comb filter 2
Trap filter 1.20 3
Trap filter 0.87 4
Trap filter 0.72 5
Trap filter 0.50 6
--------------------------------------------------------------------------------
+------------------------------------- Channel Line Rate -------+
| |
| +--------------------------------- Monochrome Input (On/Off) |
| | +----------------------------- Remove Setup from Video (On/Off) |
| | | +------------------------- Chroma Kill (On/Off) |
| | | | +--------------------- Video Decode Mode |
| | | | | +----------------- Enable AGC (On/Off) |
| | | | | | +------------- Input Video Gain (%) |
| | | | | | | +----- Enable ACC (On/Off) |
| | | | | | | | |
+---+---+---+---+---+---+-------+--------------------------------------------+--
0, 0, 0, 0, 2, 1, 100.0, 1 525
To Disable/Enable Monochrome Only Input; press: 'Q'.
To Remove/Insert Setup from Video; press: 'E'.
To Enable/Disable Chroma Kill; press: 'R'.
To Set Video Decode Mode; press: 'T'.
To Disable/Enable AGC; press: 'D'.
To Decrement/Increment Input Video Gain; press: 'F'/'G'.
To Disable/Enable ACC; press: 'C'.
Press: 'ESC' to ABORT changes and return to the previous Menu.
Press: 'Enter' to ACCEPT changes and select a different channel.
Press: 'Y' to revert back to last settings.
Press: 'Z' to set THIS channel to factory defaults.
2.) Setup Video Processing
These adjustments are made in the video path and apply to all lines
(active picture and VBI)
Video processing selections are summarized in
The actual menus are shown in
.