Basler Electric DGC-2020HD - Manual (Page 51)

9469300990 Rev B 41
•
VOLT
∗
•
AMP
∗
•
PH
∗
•
Hz
•
OIL
•
FUEL/DEF†
•
TEMP
•
BATT
∗ When set to standard, individual phase information can be automatically toggled at a rate set by the
Phase Toggle Delay setting. Navigate to the Settings, General Settings, Front Panel HMI screen and edit
Phase Toggle Delay. When the Phase Toggle Delay is set to zero, information for each phase is obtained
by pressing the Up or Down arrow keys on the front panel. When it is set to a number other than zero, the
display will toggle through the phases automatically at the rate specified by the Phase Toggle Delay
Setting.
† When a Selective Catalytic Reduction (SCR) with Diesel Exhaust Fluid (DEF) exhaust after-treatment
system is implemented, the overview screen automatically alternates the display of FUEL level and DEF
level.
When the overview screen is set to scrolling, you can select/configure the metering values that are
displayed. Up to 20 values can be displayed and these values will scroll at a delay time specified by the
user. To select a scrolling overview, navigate to the Settings, General Settings, Front Panel HMI, Scrolled
Metering screen and set the Scroll Enable setting to Enabled. The Scroll Delay setting is also found on
this screen.
To select the scrolling values, navigate to the Settings, General Settings, Front Panel HMI screen and edit
the Configurable Metering. The following parameters may be placed in the scrolling overview:
•
Alarm Silence
•
Alternate Frequency Override
•
Analog Expansion Module 1 Inputs 1 to 8
•
Analog Expansion Module 1 RTDs 1 to 8
•
Analog Expansion Module 1 Thermos 1 and 2
•
Analog Expansion Module 2 Inputs 1 to 8
•
Analog Expansion Module 2 RTDs 1 to 8
•
Analog Expansion Module 2 Thermos 1 and 2
•
Analog Expansion Module 3 Inputs 1 to 8
•
Analog Expansion Module 3 RTDs 1 to 8
•
Analog Expansion Module 3 Thermos 1 and 2
•
Analog Expansion Module 4 Inputs 1 to 8
•
Analog Expansion Module 4 RTDs 1 to 8
•
Analog Expansion Module 4 Thermos 1 and 2
•
Analog Inputs 1 to 4
•
Analog Output AVR
•
Analog Output GOV
•
Analog Output LS
•
Battery Voltage
•
Boost Pressure
•
Bus1 average voltage
•
Bus1 complex power Phase A
•
Bus1 complex power Phase B
•
Bus1 complex power Phase C
•
Bus1 Current Phase A
•
Bus1 Current Phase B
•
Bus1 Current Phase C
•
Bus1 Dead
•
Bus1 Failed
•
Contact Expansion Module 2 Inputs 1 to 10
•
Contact Expansion Module 3 Inputs 1 to 10
•
Contact Expansion Module 4 Inputs 1 to 10
•
Contact Inputs 1 to 16
•
Contact Output Prestart
•
Contact Output Run
•
Contact Output Start
•
Contact Outputs 1 to 12
•
Coolant Level Settings
•
Coolant Pressure
•
Coolant Temperature
•
Cooldown and Stop Request
•
Cooldown Request
•
Cooldown Timer Active
•
Date
•
Device ID
•
Engine Load
•
Engine Running
•
Engine Speed (RPM)
•
EPS Supplying Load
•
External Start Delay
•
Fuel Level / Diesel Exhaust Fluid Level
•
Fuel Pressure
•
Fuel Rate
•
Fuel Temperature
•
Generator average voltage
•
Generator complex power Phase A
•
Generator complex power Phase B
•
Generator complex power Phase C
DGC-2020HD Controls and Indicators