Lenze EVS9332xK - Manual (Page 464)

Appendix
Index
13
13.3
l
13.3−6 EDSVS9332K EN 8.0−07/2013
Safe torque off, 11.1−1
− device variant with, 5.8−5
− device variant without, 5.8−4
− functional test, 11.5−2, 11.5−5
− operating mode, 11.2−1
− safety relay, 11.3−1
Safety, safety engineering, 11−1
Safety engineering, 11−1
Safety function
− functional test, 11.5−2, 11.5−5
− Safe torque off, 11.1−1
Safety instructions, 2−1
− definition, 1.4−1
− layout, 1.4−1
Safety relay, 11.3−1
− Connector X11
Terminal assignment, 11.4−1
Wiring, 11.4−1
Safety relay KSR, Terminal assignment, 11.4−1
Saving, motion profiles, 6.10−6
Selection of the feedback system, 8.4−3
Setting the feedback system, 6.6−1
Setting the speed feedback, 6.6−1
Site altitude, 3.1−2
Status display, keypad XT EMZ9371BC, 7.2−2
Status word, 8.4−9
− LECOM (C0150/C0155), 9.2−3
Supply conditions, 5.4−6, 5.4−7, 5.5−5, 5.5−6, 5.6−5,
5.6−6, 5.7−5, 5.7−6, 10.3−1
Supply forms, IT system, 5.2−2
Supply forms / electrical supply conditions, 5.2−1
Switch on, 6.3−1
Switch−on, check before switching on, 6.2−1
System bus (CAN), wiring, 5.9−1
System error messages, 9.3−1
− General, 9.3−1
− Resetting, 9.3−6
T
Table of attributes, 8.6−1
Technical data, 3−1
− Current characteristics, device protection through
current derating, 3.4−1
− General data, 3.1−1
− Operating conditions, 3.1−1
Terminal assignment
− Analog inputs, 5.8−9
− Analog ouputs, 5.8−9
− Controller inhibit, 5.8−9
− Digital inputs, 5.8−9
− Digital inputs/outputs, 11.4−1
− Digital outputs, 5.8−9
− KSR safety relay, 5.8−9
− Safety relay KSR, 11.4−1
Terminal data, 5.8−2, 11.4−1
Terms
− controller, 13.2−1
− Definitions, 13.2−1
− drive, 13.2−1
Thermal monitoring, motor
− Sensorless, 2.2−1
− with PTC thermistor, 6.5−17, 6.5−18
Tni current controller, 8.4−5
Tnn speed controller, 8.4−5
Transfer methods, 6.11−1
Transfer mode, Code−oriented, 13.1−1
TRIP, 8.2−1
Troubleshooting, 9.2−1
Troubleshooting and fault elimination, 9−1
− Monitoring, 8.2−1
Current load of controller (Ixt monitoring), 8.2−5
DC−bus voltage, 8.2−9
Heatsink temperature, 8.2−8
Monitoring times for process data input objects, 8.2−3
− monitoring
bus off, 8.2−3
current load of the motor (I2 x t monitoring), 2.2−1, 8.2−7
motor temperature, 8.2−6
reset node, 8.2−3
responses, 8.2−1
Type−specific accessories, 12.2−1
U
Undervoltage threshold, DC−bus voltage, 8.2−9
V
Vpi current controller, 8.4−5
Vpn speed controller, 8.4−5
W
Warning, 8.2−1
Warranty, 1.2−2