Yokogawa Data Acquisition with PID Control CX2000 - Manual (Page 176)

6-47
IM 04L31A01-17E
6
Command
p6: First register number (30001 to 39999,
40001 to 49999, 300001 to 365535, 400001
to 465535)
p7: Type of data assigned to the register
(INT16, UINT16, INT32_B, INT32_L,
UINT32_B, UINT32_L, FLOAT_B,
FLOAT_L)
Query YM[ p1]?
Example Register the following command in command
registration number 2: Read the 32-bit signed
integer data that is assigned to registers 30003
(upper 16 bits) and 30004 (lower 16 bits) of the
slave device at address 5 into C02 of the CX.
YM2,ON,C02,C02,5,30003,INT32_B
Description • This command is valid when the serial
interface protocol is set to “Master.” For a
description of setting the serial interface, see
section 4.2.
• The settings specified by this command take
effect after the CX is power cycled.
YU Sets the contents to be sent via
e-mail
When sending the changes in the alarm status
Syntax YU p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,
p11,p12
p1: Transmitted content (ALARM)
p2: Enable/disable recipient 1 (ON, OFF)
p3: Enable/disable recipient 2 (ON, OFF)
p4: Enable/disable alarm transmission of alarm
number 1 (ON, OFF)
p5: Enable/disable alarm transmission of alarm
number 2 (ON, OFF)
p6: Enable/disable alarm transmission of alarm
number 3 (ON, OFF)
p7: Enable/disable alarm transmission of alarm
number 4 (ON, OFF)
p8: Enable/disable attachment of instantaneous
data (ON, OFF)
p9: Enable/disable attachment of source URL
(ON, OFF)
p10: Subject (up to 32 characters)
p11: Header 1 (up to 64 characters)
p12: Header 2 (up to 64 characters)
Query YU[ p1]?
Example Transmit alarms of alarm numbers 1 to 4
including instantaneous data but not including
the source URL to recipient 1. The subject is
“ALM”, and the header is “LP2”.
YUALARM,ON,OFF,ON,ON,ON,ON,ON,OFF,
ALM,LP2
When sending e-mail at scheduled times
Syntax YU p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,
p11,p12
p1: Transmitted content (TIME)
p2: Enable/disable recipient 1 (ON, OFF)
p3: Interval for sending e-mail to recipient 1
(1H, 2H, 3H, 4H, 6H, 8H, 12H, 24H)
p4: Time when sending e-mail to recipient 1
(HH:MM)
p5: Enable/disable recipient 2 (ON, OFF)
p6: Interval for sending e-mail to recipient 2 (1H,
2H, 3H, 4H, 6H, 8H, 12H, 24H)
p7: Time when sending e-mail to recipient 2
(HH:MM)
p8: Enable/disable attachment of instantaneous
data (ON, OFF)
p9: Enable/disable attachment of source URL
(ON, OFF)
p10: Subject (up to 32 characters)
p11: Header 1 (up to 64 characters)
p12: Header 2 (up to 64 characters)
Query YU[ p1]?
Example Send e-mail at 17 hours 15 minutes every day to
recipient 1. Do not include instantaneous data
but include the source URL. The subject is
“GOOD”, and the header is “LP2”.
YUTIME,ON,24H,17:15,OFF,,,OFF,ON,
GOOD,LP2
When sending system notifications
Syntax YU p1,p2,p3,p4,p5,p6,p7
p1: Transmitted content (SYSTEM)
p2: Enable/disable recipient 1 (ON, OFF)
p3: Enable/disable recipient 2 (ON, OFF)
p4: Enable/disable attachment of source URL
(ON, OFF)
p5: Subject (up to 32 characters)
p6: Header 1 (up to 64 characters)
p7: Header 2 (up to 64 characters)
Query YU[ p1]?
Example Send system notification e-mail messages
including the source URL to recipient 1. The
subject is “SystemAlert”, and the header is “LP2”.
YUSYSTEM,ON,OFF,ON,SystemAlert,LP2
When sending report generation notifications
Syntax YU p1,p2,p3,p4,p5,p6,p7
p1: Transmitted content (REPORT)
p2: Enable/disable recipient 1 (ON, OFF)
p3: Enable/disable recipient 2 (ON, OFF)
p4: Enable/disable attachment of source URL
(ON, OFF)
p5: Subject (up to 32 characters)
p6: Header 1 (up to 64 characters)
p7: Header 2 (up to 64 characters)
Query YU[ p1]?
6.7 Basic Setting Commands (Measurement)