beautypg.com

Mrp commands on switch b, Mrp commands on switch c – Brocade FastIron Ethernet Switch Platform and Layer 2 Switching Configuration Guide User Manual

Page 92

background image

device(config-vlan-2-mrp-1)#enable

device(config-vlan-2-mrp-1)#exit

device(config-vlan-2)#exit

The following commands configure the customer VLANs. The customer VLANs must contain both the
ring interfaces as well as the customer interfaces.

device(config)#vlan 30

device(config-vlan-30)#tag ethernet 1/1 to 1/2

device(config-vlan-30)#tag ethernet 2/1

device(config-vlan-30)#exit

device(config)#vlan 40

device(config-vlan-40)#tag ethernet 1/1 to 1/2

device(config-vlan-40)#tag ethernet 4/1

device(config-vlan-40)#exit

The following commands configure topology group 1 on VLAN 2. The master VLAN is the one that
contains the MRP configuration. The member VLANs use the MRP parameters of the master VLAN.
The control interfaces (the ones shared by the master VLAN and member VLAN) also share MRP
state.

device(config)#topology-group 1

device(config-topo-group-1)#master-vlan 2

device(config-topo-group-1)#member-vlan 30

device(config-topo-group-1)#member-vlan 40

MRP commands on Switch B

The commands for configuring Switches B, C, and D are similar to the commands for configuring
Switch A, with two differences: the nodes are not configured to be the ring master. Omitting the
master command is required for non-master nodes.

device(config)#vlan 2

device(config-vlan-2)#tag ethernet 1/1 to 1/2

device(config-vlan-2)#metro-ring 1

device(config-vlan-2-mrp-1)#name "Metro A"

device(config-vlan-2-mrp-1)#ring-interface ethernet 1/1 ethernet 1/2

device(config-vlan-2-mrp-1)#enable

device(config-vlan-2)#exit

device(config)#vlan 30

device(config-vlan-30)#tag ethernet 1/1 to 1/2

device(config-vlan-30)#tag ethernet 2/1

device(config-vlan-30)#exit

device(config)#vlan 40

device(config-vlan-40)#tag ethernet 1/1 to 1/2

device(config-vlan-40)#tag ethernet 4/1

device(config-vlan-40)#exit

device(config)#topology-group 1

device(config-topo-group-1)#master-vlan 2

device(config-topo-group-1)#member-vlan 30

device(config-topo-group-1)#member-vlan 40

MRP commands on Switch C

device(config)#vlan 2

device(config-vlan-2)#tag ethernet 1/1 to 1/2

device(config-vlan-2)#metro-ring 1

device(config-vlan-2-mrp-1)#name "Metro A"

device(config-vlan-2-mrp-1)#ring-interface ethernet 1/1 ethernet 1/2

device(config-vlan-2-mrp-1)#enable

device(config-vlan-2)#exit

device(config)#vlan 30

device(config-vlan-30)#tag ethernet 1/1 to 1/2

device(config-vlan-30)#tag ethernet 2/1

device(config-vlan-30)#exit

device(config)#vlan 40

device(config-vlan-40)#tag ethernet 1/1 to 1/2

device(config-vlan-40)#tag ethernet 4/1

MRP commands on Switch B

92

FastIron Ethernet Switch Platform and Layer 2 Switching Configuration Guide

53-1003086-04