HEIDENHAIN TNC 426B (280 472) ISO programming - Manual (Page 388)

G functions
Coordinate transformations
G53 Datum shift in datum table
G54 Datum shift in program
G28 Mirror image
G73 Rotation of the coordinate system
G72 Scaling factor (reduce or enlarge contour)
G80 Tilting the Working Plane
Cycles for multipass milling
G60 Running point tables (not TNC 410)
G230 Multipass milling of smooth surfaces
G231 Multipass milling of tilted surfaces
Special Cycles
* G04 Dwell time with F seconds
G36Oriented spindle stop
* G39 Program call
G62 Tolerance deviation for fast contour milling (not TNC 410)
Define machining plane
G17 Working plane: X/Y; tool axis: Z
G18 Working plane: Z/X; tool axis: Y
G19 Working plane: Y/Z; tool axis: X
G20 Tool axis IV
Dimensions
G90 Absolute dimensions
G91 Incremental dimensions
Unit of measure
G70 Inches (set at start of program)
G71 Millimeters (set at start of program)
Other G functions
G29 Transfer the last nominal position value as a pole (circle center)
G38 Program run STOP
* G51 Next tool number (with central tool file)
G55 Programmable probing function
* G79 Call the cycle
* G98 Set label number
*) Non-modal function
G functions
Tool movements
G00 Straight-line interpolation, Cartesian coordinates, rapid traverse
G01 Straight-line interpolation, Cartesian coordinates
G02 Circular interpolation, Cartesian coordinates, clockwise
G03 Circular interpolation, Cartesian coordinates, counterclockwise
G05 Circular interpolation, Cartesian coordinates, without indication of direction
G06Circular interpolation, Cartesian coordinates, tangential contour approach
* G07 Paraxial positioning block
G10 Straight-line interpolation, polar coordinates, rapid traverse
G11 Straight-line interpolation, polar coordinates
G12 Circular interpolation, polar coordinates, clockwise
G13 Circular interpolation, polar coordinates, counterclockwise
G15 Circular interpolation, polar coordinates, without indication of direction
G16 Circular interpolation, polar coordinates, tangential contour approach
Chamfer/Rounding/Approach contour/Depart contour
* G24 Chamfer with length R
* G25 Corner rounding with radius R
* G26Tangential contour approach with radius R
* G27 Tangential contour departure with radius R
Define the tool
* G99
With tool number T, length L, radius R
Tool radius compensation
G40 No tool radius compensation
G41 Tool radius compensation, left of the contour
G42 Tool radius compensation, right of the contour
G43 Paraxial compensation for G07, lengthening
G44 Paraxial compensation for G07, shortening
Blank form definition for graphics
G30 (G17/G18/G19) min. point
G31 (G90/G91) max. point
Drilling cycles
G83 Pecking
G84 Tapping with a floating tap holder
G85 Rigid tapping
G86Thread cutting (not TNC 410)
G200 Drilling
G201 Reaming
G202 Boring
G203 Universal drilling
G204 Back boring
G205 Universal peck drilling (only NC software 280 474-xx)
G206Tapping with floating tap holder (only NC software 280 474-xx)
G207 Rigid tapping (only NC software 280 474-xx)
G208 Bore milling (only NC software 280 474-xx)
Cycles for milling pockets, studs and slots
G74 Slot milling
G75 Rectangular pocket milling in clockwise direction
G76Rectangular pocket milling in counterclockwise direction
G77 Circular pocket milling in clockwise direction
G78 Circular pocket milling in counterclockwise direction
G210 Slot milling with reciprocating plunge
G211 Round slot with reciprocating plunge
G212 Rectangular pocket finishing
G213 Rectangular stud finishing
G214 Circular pocket finishing
G215 Circular stud finishing
Cycles for creating point patterns
G220 Circular pattern
G221 Linear pattern
SL cycles, group 1
G37 Contour geometry, list of subcontour program numbers
G56Pilot drilling
G57 Rough-out
G58 Contour milling in clockwise direction (finishing)
G59 Contour milling, counterclockwise (finishing)
SL cycles, group 2 (not TNC 410)
G37 Contour geometry, list of subcontour program numbers
G120 Contour data (applies to G121 to G124)
G121 Pilot drilling
G122 Rough-out
G123 Floor finishing
G124 Side finishing
G125 Contour train (machining open contour)
G127 Cylinder surface
G functions and addresses
Addresses
Add. Function
% Start of program
% Program call
# Datum number with G53
A Rotation about X-axis
B Rotation about Y-axis
C Rotation about Z-axis
D Q-parameter definitions
DL Wear compens. of length with T
DR Wear compens. of radius with T
E Tolerance with M112 and M124
F Feed rate
F Dwell time with G04
F Scaling factor with G72
F Reduction factor F with M103
G G functions
H Polar coordinate angle
H Angle of rotation with G73
H Max. permissible angle with M112
I X coordinate of the
circle center/pole
J Y coordinate of the
circle center/pole
K Z coordinate of the
circle center/pole
L Setting a label number
with G98
L Jump to a label number
L Tool length with G99
Add. Function
M M functions
N Block number
P Cycle parameters
in machining cycles
P Value or Q parameter in
Q-parameter definition
Q Q parameter
R Polar coordinate radius
R Circular radius with G02/G03/G05
R Rounding radius with
G25/G26/G27
R Tool radius with G99
S Spindle speed
S Oriented spindle stop with G36
T Tool definition with G99
T Tool call
T Next tool with G51
U Axis parallel to X axis
V Axis parallel to Y axis
W Axis parallel to Z axis
X X axis
Y Y axis
Z Z axis
* End of block
Vkurzanl.pm6 29.06.2006, 08:07 326