HEIDENHAIN TNC 426B (280 472) ISO programming - Manual (Page 359)

14 Tabellen und Übersichten 344
14.1 Gener
al User P
ar
amet
ers
Configure tool table (To omit from the table: enter 0);
Column number in the tool table for
MP7266.0 Tool name – NAME: 0 to 28; column width: 16 characters
MP7266.1 Tool length – L: 0 to 28; column width: 11 characters
MP7266.2 Tool radius – R: 0 to 28; column width: 11 characters
MP7266.3 Tool radius 2 – R2: 0 to 28; column width: 11 characters (not TNC 410)
MP7266.4 Oversize length – DL: 0 to28; column width: 8 characters
MP7266.5 Oversize radius – DR: 0 to28; column width: 8 characters
MP7266.6 Oversize radius 2 – DR2: 0 to 28; column width: 8 characters (not TNC 410)
MP7266.7 Tool locked – TL: 0 to28; column width: 2 characters
MP7266.8 Replacement tool – RT: 0 to28; column width: 3 characters
MP7266.9 Maximum tool life – TIME1: 0 to28; column width: 5 characters
MP7266.10 Maximum tool life for TOOL CALL – TIME2: 0 to 28; column width: 5 characters
MP7266.11 Current tool life — CUR. TIME: 0 to 28; column width: 8 characters
MP7266.12 Tool comment – DOC: 0 to 28; column width: 16 characters
MP7266.13 Number of teeth – CUT.: 0 to 28; column width: 4 characters
MP7266.14 Tolerance for wear detection in tool length – LTOL: 0 to 28; column width: 6 characters
MP7266.15 Tolerance for wear detection in tool radius – RTOL: 0 to 28; column width: 6 characters
MP7266.16 Cutting direction – DIRECT.: 0 to 28; column width: 7 characters
MP7266.17 PLC status – PLC: 0 to 28; column width: 9 characters
MP7266.18 Offset of the tool in the tool axis in addition to MP6530 – TT:L-OFFS: 0 to 28;
column width: 11 characters
MP7266.19 Offset of the tool between stylus center and tool center — TT:R-OFFS: 0 to 28;
column width: 11 characters
MP7266.20 Tolerance for break detection in tool length – LBREAK.: 0 to 28; column width 6 characters
MP7266.21 Tolerance for break detection in tool radius – RBREAK.: 0 to 28; column width 6 characters
MP7266.22 Tool length (Cycle 22) – LCUTS: 0 to 28; column width: 11
MP7266.23 Maximum plunge angle (Cycle 22) – ANGLE.: 0 to 28; column width: 7 characters
MP7266.24 Tool type – TYP: 0 to 28; column width: 5 characters (only for conversational dialog, not TNC 410)
MP7266.25 Tool material – TMAT: 0 to 28; column width: 16 characters
(only for conversational programming, not TNC 410)
MP7266.26 Cutting data table – CDT: 0 to 28; column width: 16 characters (only for conversational dialog,
not TNC 410)
MP7266.17 PLC value – PLC-VAL: 0 to 28; column width: 9 characters (not TNC 410)
Rkap14.pm6 29.06.2006, 08:07 344