Verilink XEL XSP-100 SHARK IAP (9SA-USRS-9.0R1.02) Product Manual User Manual
Page 177

Chapter 6: Using the Command Line Interface (CLI)
SHARK™ IAD User’s Guide
XEL P/N & Release 9SA-USRS-9.0R1.02
Chapter 6-61
(XCON-IF wan1-src-time-slot-2 dst-time-slot)>>set 4
(XCON-IF wan1-src-time-slot-2 dst-time-slot)>>wan1 src-time-slot-9 dst-module
(XCON-IF wan1-src-time-slot-9 dst-module)>>set vc1
(XCON-IF wan1-src-time-slot-9 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-9 dst-time-slot)>>set 5
(XCON-IF wan1-src-time-slot-9 dst-time-slot)>>wan1 src-time-slot-15 dst-module
(XCON-IF wan1-src-time-slot-15 dst-module)>>set vc1
(XCON-IF wan1-src-time-slot-15 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-15 dst-time-slot)>>set 6
(XCON-IF wan1-src-time-slot-15 dst-time-slot)>>wan1 src-time-slot-7 dst-module
(XCON-IF wan1-src-time-slot-7 dst-module)>>set vc1
(XCON-IF wan1-src-time-slot-7 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-7 dst-time-slot)>>set 7
(XCON-IF wan1-src-time-slot-7 dst-time-slot)>>wan1 src-time-slot-6 dst-module
(XCON-IF wan1-src-time-slot-6 dst-module)>>set vc1
(XCON-IF wan1-src-time-slot-6 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-6 dst-time-slot)>>set 8
(XCON-IF wan1-src-time-slot-6 dst-time-slot)>>up
(XCON-IF)>>
3. The following program voice2 as the destination for this cross connect
group. These commands route 4 channels from any source and in any
sequence. The source modules are the modules in WAN slot 1, DS0s 1, 5,
and 13 and in WAN slot 2, DS0 23 to the destination which is the module
in voice slot 2, circuits 5 - 8.
(XCON-IF)>>wan1
(XCON-IF wan1)>>src-time-slot-1 dst-module
(XCON-IF wan1-src-time-slot-1 dst-module)>>set vc2
(XCON-IF wan1-src-time-slot-1 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-1 dst-time-slot)>> set 5
(XCON-IF wan1-src-time-slot-1 dst-time-slot)>>wan1 src-time-slot-5 dst-module
(XCON-IF wan1-src-time-slot-5 dst-module)>>set vc2
(XCON-IF wan1-src-time-slot-5 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-5 dst-time-slot)>>set 6
(XCON-IF wan1-src-time-slot-5 dst-time-slot)>>wan1 src-time-slot-13 dst-module
(XCON-IF wan1-src-time-slot-13 dst-module)>>set vc1
(XCON-IF wan1-src-time-slot-13 dst-module)>>dst-time-slot
(XCON-IF wan1-src-time-slot-13 dst-time-slot)>>set 7
(XCON-IF wan1-src-time-slot-13 dst-time-slot)>>wan2 src-time-slot-23 dst-module
(XCON-IF wan2-src-time-slot-23 dst-module)>>set vc2
(XCON-IF wan2-src-time-slot-23 dst-module)>>dst-time-slot
(XCON-IF wan2-src-time-slot-23 dst-time-slot)>>set 8
(XCON-IF wan2-src-time-slot-23 dst-time-slot)>>up
(XCON-IF)>>
4. The following program the router as the destination for this cross connect group. These
commands route 4 channels from WAN slot 1with DS0s 13 - 16 to the destination, which
is the router module channels 13 – 16.
(XCON-IF)>>wan1
(XCON-IF wan1)>>src-time-slot-13 dst-module
(XCON-IF wan1 src-time-slot-13 dst-module)>> set rtr
(XCON-IF wan1 src-time-slot-13 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-13 dst-time slot)>>set 13
(XCON-IF wan1 src-time-slot-13 dst-time slot)>>wan1 src-time-slot-14 dst-module
(XCON-IF wan1 src-time-slot-14 dst-module)>> set rtr
(XCON-IF wan1 src-time-slot-14 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-14 dst-time-slot)>>set 14
(XCON-IF wan1 src-time-slot-14 dst-time-slot)>>wan1 src-time-slot-15 dst-module