Brocade Virtual ADX MIB Reference (Supporting ADX v03.1.00) - Manual (Page 70)

58 Brocade Virtual ADX MIB Reference
53-1003312-01
Switch port information
snSwIfStatsMacStations
brcdIp.1.1.3.3.5.1.44
Syntax: Integer32 Read only Shows the total number of MAC Stations connected to the
interface.
snSwIfStatsLinkChange
brcdIp.1.1.3.3.5.1.45
Syntax: Counter Read only Shows the total number of link state changes on the interface.
snSwIfInOctets
brcdIp.1.1.3.3.5.1.46
Syntax: Octet string Read only Shows the total number of octets received on the interface,
including framing characters. This object is a 64-bit counter of the
ifInOctets object defined in RFC 1213. The octet string is in
big-endian byte order.
This object has eight octets.
snSwIfOutOctets
brcdIp.1.1.3.3.5.1.47
Syntax: Octet string Read only Shows the total number of octets transmitted out of the interface,
including framing characters. This object is a 64-bit counter of the
ifOutOctets object, defined in RFC 1213. The octet string is in
big-endian byte order.
This object has eight octets.
snSwIfStatsInBitsPerSec
brcdIp.1.1.3.3.5.1.48
Syntax: Gauge Read only Shows the number of bits per second received on the interface
over a five-minute interval.
snSwIfStatsOutBitsPerSec
brcdIp.1.1.3.3.5.1.49
Syntax: Gauge Read only Shows the number of bits per second transmitted out of the
interface over a five-minute interval.
snSwIfStatsInPktsPerSec
brcdIp.1.1.3.3.5.1.50
Syntax: Gauge Read only Shows the number of packets per second received on the
interface over a five-minute interval.
snSwIfStatsOutPktsPerSec
brcdIp.1.1.3.3.5.1.51
Syntax: Gauge Read only Shows the number of packets per second transmitted out of the
interface over a five-minute interval.
snSwIfStatsInUtilization
brcdIp.1.1.3.3.5.1.52
Syntax: Integer Read only Indentifies the input network utilization in hundredths of a
percent over a five-minute interval.
Valid values: 0 – 10000.
snSwIfStatsOutUtilization
brcdIp.1.1.3.3.5.1.53
Syntax: Integer Read only Shows the output network utilization in hundredths of a percent
over a five-minute interval.
Valid values: 0 – 10000.
NOTE: Ethernet devices must allow a minimum idle period between transmission of frames known as interframe
gap (IFG) or interpacket gap (IPG). The gap provides a brief recovery time between frames to allow devices
to prepare to receive the next frame. The minimum IFG is 96 bit times, which is 9.6 microseconds for 10
Mbps Ethernet, 960 nanoseconds for 100 Mbps Ethernet, and 96 nanoseconds for 1 Gbps Ethernet. In
addition, to account for the bit rate on the port, port utilization should also account for the IFG, which
normally is filtered by the packet synchronization circuitry.
Refer to the etherHistoryUtilization objects in the RFC 1757: Remote Network Monitoring Management
Information Base for details.
snSwIfStatsInKiloBitsPerSec
brcdIp.1.1.3.3.5.1.54
Syntax: Unsigned32 Read-only Shows the bit rate, in kilobits per second, received on a 10
Gigabit or faster interface within a five minute interval.
Name, OID, and Syntax Access Description