Teledyne LeCroy Sierra M6-1 SAS_SATA Protocol Analyzer User Manual User Manual
Sierra m6-1 sas/sata protocol analyzer user manual
Table of contents
Document Outline
- Contents
- Introduction
- 1.1 Analyzer Overview
- 1.2 Features
- 1.3 Receiving Your Analyzer
- 1.4 Unpacking the Analyzer
- 1.5 Analyzer Features
- 1.6 Installing Your Analyzer
- 1.7 Cascading Sierra Analyzers
- 1.8 Connecting via Ethernet
- 1.9 Launching Your Analyzer
- 1.10 Operating in Simulation Mode
- 1.11 Teledyne LeCroy SAS/SATA Protocol Suite Menu Options and Toolbars
- Protocol Analysis
- 2.1 Easy Mode (Pre-Defined Setups)
- 2.2 Main Window
- 2.3 Project Tree
- 2.4 Capture Tab Fields
- 2.5 SAS/SATA Software Menus and Toolbars
- 2.6 Start Recording
- 2.7 CrossSync Control Panel
- 2.8 Save Workspace
- 2.9 Saving a Trace Capture
- 2.10 Projects
- 2.11 Patterns and Data Capture Setup
- 2.12 Protocol Errors
- 2.13 Trigger Setup
- 2.14 Project Settings
- 2.15 Analyzer Settings
- 2.16 Advanced Mode (User-Defined)
- 2.17 Project Settings
- 2.18 Creating a Data Block
- 2.19 Counter
- Display Manipulation
- 3.1 Viewer Display
- 3.2 Trace Properties
- 3.3 Analysis
- 3.3.1 Analysis Toolbar
- 3.3.2 Decoding Assignments
- 3.3.3 Packet View
- 3.3.4 Changing the Default View
- 3.3.5 Spreadsheet View
- 3.3.6 Column View
- 3.3.7 Text View
- 3.3.8 Frame Inspector View
- 3.3.9 Waveform Display
- 3.3.10 Statistical Report
- Generating Statistical Read/Write Report
- Report between Cursors
- Report between Events
- Statistical Report Content
- Report Options
- General Report
- Primitive Report
- Bus Condition Report
- ATA Command Report
- Time out of ATA Command Report
- ATAPI Report
- Protocol Error Report
- Others Report
- SSP Transport Report (SAS)
- SMP Transport Report (SAS)
- STP Transport Report (SAS)
- SCSI Command Report (SAS)
- SMP Command Report (SAS)
- Task Command Report (SAS)
- SAS Address Report (SAS)
- Lanes Report (SAS)
- Read/Write Command Report (SAS)
- Performance Report (SAS)
- Performance Report (SATA)
- FIS Report (SATA)
- Queue Command Report (SATA)
- PM Statistic Report (SATA)
- PM Performance Report (SATA)
- Read Write Command Report (SATA)
- 3.3.11 Statistical Report Toolbar
- 3.3.12 Formatting the Statistical Report View
- 3.3.13 Histogram View
- 3.3.14 Bus Utilization View
- 3.3.15 Bus Utilization Buttons
- 3.3.16 Data Report
- 3.3.17 Compare Two Data Payloads
- 3.4 Running Verification Script Engine (VSE)
- 3.5 Navigation + View Toolbar
- 3.6 Packet View Toolbar
- 3.7 Port Status
- 3.8 Toolbars
- 3.9 Status Bar
- 3.10 Using the Cursors and Bookmarks
- 3.11 Display Configuration
- 3.12 Set Port Alias
- 3.13 SAS Address Alias (SAS only)
- 3.14 TxRx Vout & Preemphasis
- 3.15 Preferences
- 3.16 Floating License
- 3.17 External Trig Setting
- 3.18 Update Device
- 3.19 User-Defined Decoding
- 3.20 Help Menu
- 3.21 Setup Menu
- 3.22 Find DUT
- 3.23 Power Source Control
- InFusion Overview
- 4.1 Key Features
- 4.2 Interface
- 4.3 Port Configuration for InFusion
- 4.4 InFusion Scenarios
- 4.5 Scenario Events
- 4.6 Scenario Actions
- 4.7 Summary of Scenario Creation
- 4.8 Creating Global Rules
- 4.9 Example 1: Creating a Single Event and Action that Removes a Primitive
- 4.10 Example 2: Wait for a Primitive and Replace It with an Error
- 4.11 Example 3: Creating OR Conditions
- 4.12 Example 4: Multiple Triggers and Actions
- 4.13 Example 5: Multiple Actions on a Single Event
- 4.14 Example 6: Using Timers
- 4.15 Creating a Sequence
- 4.16 Example 7: Creating Two Sequences and Global Rules
- 4.17 Example 8: Creating a Sequence With Many States #1
- 4.18 Example 9: Creating a Sequence With Many States #2
- 4.19 Downloading Scenarios
- 4.20 Running Scenarios
- 4.21 Scenario Batch Files
- Creating a Pattern Generator File
- China Restriction of Hazardous Substances Table
- How to Contact Teledyne LeCroy
- Index