Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications User Manual
Yaskawa ac drive-l1000e, Technical manual, Ac drive for elevator applications
YASKAWA AC Drive-L1000E
AC Drive for Elevator Applications
Technical Manual
MANUAL NO. SIEP YAIL1E 01A
Models: 200 V Class: 3.7 to 110 kW (5 to 150 HP)
400 V Class: 4.0 to 132 kW (5 to 175 HP)
To properly use the product, read this manual thoroughly and retain
for easy reference, inspection, and maintenance. Ensure the end user
receives this manual.
Type: CIMR-LEA
Receiving
Mechanical Installation
Electrical Installation
Parameter Details
Troubleshooting
Specifications
Parameter List
Standards Compliance
Quick Reference Sheet
1
2
3
4
5
6
7
8
A
B
C
D
E
1
2
3
4
5
6
7
8
A
B
C
D
E
Start-Up Programming &
Operation
Periodic Inspection &
Maintenance
Peripheral Devices &
Options
MEMOBUS/Modbus
Communications
PWR
LED
MON
ITO
R JV
OP-1
84
RUN
DS1
DS2
RUN
DS
1
DS
2
STAT
US
REA
DY
RUN
ALARM(
RUN
)
PGO
H,LT
BB,H
BB
EF,SE
Othe
r Fau
lt
OV,U
V
OH
,OL
OC
,GF,S
C,PGO
CPF
,OFA
,OFB
,OFC
:LIGHT
:BL
INK
:LIG
HT
OFF
Document Outline
- Quick Reference
- Preface & General Safety
- Receiving
- Mechanical Installation
- Electrical Installation
- 3.1 Section Safety
- 3.2 Standard Connection Diagram
- 3.3 Main Circuit Connection Diagram
- 3.4 Terminal Block Configuration
- 3.5 Terminal Cover
- 3.6 LED Monitor Operator and Front Cover
- 3.7 Main Circuit Wiring
- 3.8 Control Circuit Wiring
- 3.9 Control I/O Configuration
- 3.10 Connect to a PC
- 3.11 MEMOBUS/Modbus Termination
- 3.12 Wiring Checklist
- Start-Up Programming & Operation
- 4.1 Section Safety
- 4.2 Using the LED Monitor/Digital Operator
- 4.3 The Drive and Programming Modes
- 4.4 Start-Up Flowcharts
- Flowchart A: Installation, Wiring, Basic Setup for Motor and Elevator
- Power On
- Control Mode Selection
- Motor Rotation Direction Setup
- PG Encoder Setup
- Digital Operator Display Unit Selection
- Flowchart B: Auto-Tuning for Induction Motors
- Flowchart C: Auto-Tuning for PM Motors
- Flowchart D: PG Encoder Offset Auto-Tuning
- 4.5 Auto-Tuning
- 4.6 Setup Procedure for Elevator Applications
- 4.7 Setup Troubleshooting and Possible Solutions
- Cannot Change Parameter Settings
- Motor Does Not Rotate Properly after Pressing RUN Button or after Entering External Up/Down Command
- Motor is Too Hot
- Drive Does Not Allow Selection the Desired Auto-Tuning Mode
- Electrical Noise From Drive or Output Lines When the Drive is Operating
- Ground Fault Circuit Interrupter (ELCB/GFCI) Trips During Run
- Encoder Offset (E5-11) Set during Auto-Tuning (Rotational or Stationary) Consistently Differs by 30 Degrees or More
- Riding Comfort Related Problems
- 4.8 Verifying Parameter Settings and Backing Up Changes
- Parameter Details
- Troubleshooting
- Periodic Inspection & Maintenance
- Peripheral Devices & Options
- 8.1 Section Safety
- 8.2 Drive Options and Peripheral Devices
- 8.3 Connecting Peripheral Devices
- 8.4 Option Card Installation
- 8.5 Installing Peripheral Devices
- Dynamic Braking Options
- Installing a Molded Case Circuit Breaker (MCCB)
- Installing a Magnetic Contactor at the Power Supply Side
- Connecting an AC Reactor or a DC Link Choke
- Connecting a Surge Absorber
- Connecting a Noise Filter
- Fuse/Fuse Holder
- Attachment for External Heatsink Mounting
- Installing a Motor Thermal Overload (oL) Relay on the Drive Output
- Specifications
- Parameter List
- MEMOBUS/Modbus Communications
- C.1 MEMOBUS/Modbus Configuration
- C.2 Communication Specifications
- C.3 Connecting to a Network
- C.4 MEMOBUS/Modbus Setup Parameters
- C.5 Drive Operations by MEMOBUS/Modbus
- C.6 Communications Timing
- C.7 Message Format
- C.8 Message Examples
- C.9 MEMOBUS/Modbus Data Table
- C.10 Enter Command
- C.11 Communication Errors
- C.12 Self-Diagnostics
- Standards Compliance
- Quick Reference Sheet
- Index
- Revision History