Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications - Manual (Page 396)

B.3 Parameter Table
396 YASKAWA ELECTRIC SIEP YAIL1E 01A YASKAWA AC Drive L1000E Technical Manual
■ o2: Digital Operator Keypad Functions
■ o3: Copy Function
o1-21
(576H)
Roping Ratio
Sets the roping ratio.
1: 1:1
2: 1:2
3: 1:3
4: 1:4 Default: 2
Min: 1
Max: 4
241
o1-22
(577H)
Mechanical Gear Ratio
Sets the ratio of the gear installed for display unit calculations.
Default: <2>
Min: 0.10
Max: 100.00 241
o1-23
(174H)
HBB Non Display Select Shows and hides HBB on the digital operator while the safety signal is being input.
0: Show HBB
1: Hide HBB
Default: 0
Min: 0
Max: 1 242
<1> The control mode determines the selections available. In V/f Control, only settings 1 through 3 are permitted.
<2> Default setting is determined by the control mode (A1-02).
<5> This parameter appears when the drive displays user-set units (o1-03 = 3).
<6> Default setting and setting range changes when inches are selected for the length units (o1-12 = 1). The setting range becomes 3.70 to 78.00
inches, and the default becomes 15.70 inches.
No. (Addr.) Name Description Setting Page
o2-01
(505H)
<1> Parameter setting value is not reset to the default value when the drive is initialized.
LO/RE Key Function Selection
0: Disabled
1: Enabled. LO/RE key switches between LOCAL and REMOTE operation.
Default: 0
Min: 0
Max: 1 242
o2-02
(506H)
STOP Key Function Selection
0: Disabled. STOP key is disabled in REMOTE operation.
1: Enabled. STOP key is always enabled.
Default: 0
Min: 0
Max: 1 242
o2-03
(507H)
User Parameter Default Value 0: No change.
1: Set defaults. Saves parameter settings as default values for a User Initialization.
2: Clear all. Clears the default settings that have been saved for a User Initialization.
Default: 0
Min: 0
Max: 2 243
o2-04
(508H)
<1>
Drive Model Selection
Enter the drive model. Setting required only if installing a new control board.
Default: Determined by
drive capacity
Min: –
Max: –
243
o2-05
(509H)
Speed Reference Setting Method
Selection
0: ENTER key must be pressed to enter a speed reference.
1: ENTER key is not required. The speed reference can be adjusted using the up and down
arrow keys only.
Default: 0
Min: 0
Max: 1 243
o2-06
(50AH)
Operation Selection when Digital
Operator is Disconnected
0: The drive continues operating if the digital operator is disconnected.
1: A fault is triggered (oPr) and the motor coasts to stop.
Default: 0
Min: 0
Max: 1 244
o2-09
(50DH)
Reserved – – –
No. (Addr.) Name Description Setting Page
o3-01
(515H)
Copy Function Selection
0: Copy select
1: INV
→ OP READ (Read parameters from the drive, saving them onto the digital operator.)
2: OP → INV WRITE (Copy parameters from the digital operator, writing them to the drive.)
3: OP ↔ INV VERIFY (Verify parameter settings on the drive to check if they match the data
saved on the operator.)
To read the drive’s parameter settings into the digital operator, set o3-02 to 1 (to allow reading).
Default: 0
Min: 0
Max: 3 244
o3-02
(516H)
Copy Allowed Selection Selects whether the read operation (o3-01 = 1) is enabled or disabled.
0: Read operation prohibited
1: Read operation allowed
Default: 0
Min: 0
Max: 1 244
No. (Addr.) Name Description Setting Page
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_