Rockwell Automation 57C570 AutoMax PC3000 User Manual User Manual
Page 224

20Ć6
20.3.2
Preparing a New AutoMax PC3000 Processor Card
for Installation
To prepare a new AutoMax PC3000 Processor card for installation,
follow these steps:
Step 1.
Remove the new card from its shipping container and
from its antiĆstatic bag. Be careful not to touch the
components or the surface.
Step 2.
Make sure jumper JP2 on the new AutoMax PC3000
Processor card is set the same as that on the old
AutoMax PC3000 Processor card.
Step 3.
Remove the paper strip that covers one end of the
battery.
20.3.3
Installing a New AutoMax PC3000 Processor Card
To install a new AutoMax PC3000 Processor card, follow the steps
for the AutoMax PC3000 model you are using:
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Installing the card into an PC3000
Packaged Version:
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Installing the card into a PC
chassis:
ББББББББББ
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
ББББББББББ
Step 1.
Insert the card into the
chassis. While firmly
pressing down on the card,
use a frontĆtoĆback rocking
motion to seat the card in
the socket. Make sure the
goldĆstriped bottom edge
of the board sits firmly in
the expansion slot socket
and that the bracket of the
board is in the
corresponding groove.
БББББББББББ
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
БББББББББББ
Step 1.
Insert the card into the
computer chassis. While
firmly pressing down on
the card, use a
frontĆtoĆback rocking
motion to seat the card in
the socket. Make sure the
goldĆstriped bottom edge
of the board sits firmly in
the expansion slot socket
and that the bracket of the
board is in the
corresponding groove.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 2.
Using a screwdriver,
secure the card with the
slot cover's screw.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 2.
Using a screwdriver,
secure the card with the
slot cover's screw.
ББББББББББ
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
ББББББББББ
Step 3.
Connect the ribbon cable
of the serial card to the
connector on the AutoMax
PC3000 Processor card.
БББББББББББ
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
БББББББББББ
Step 3.
If you have an AutoMax
PC3000 Serial card
installed, connect the
ribbon cable of the serial
card to the connector on
the AutoMax PC3000
Processor card.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 4.
Using a screwdriver,
replace the hold down
clamp.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 4.
Replace the computer
chassis' cover.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 5.
Close the chassis door,
and remount the chassis if
needed.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 5.
Reconnect the DCSĆNET
network and AĆB Remote
I/O cables.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 6.
Reconnect the DCSĆNET
network and AĆB Remote
I/O cables.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 6.
Plug in the power cord,
and turn on the computer.