Rockwell Automation 57C570 AutoMax PC3000 User Manual User Manual
Page 221

20Ć3
20.2.3
ReĆinstalling the AutoMax PC3000 Processor Card
To reĆinstall the AutoMax PC3000 Processor card, follow the steps
for the AutoMax PC3000 model you are using:
БББББББББББ
БББББББББББ
Replacing the card in a PC3000
Packaged Version:
ББББББББББ
ББББББББББ
Replacing the card in a PC chassis:
БББББББББББ
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
БББББББББББ
Step 1.
Insert the card into the
chassis. While firmly
pressing down on the card,
use a frontĆtoĆback rocking
motion to seat the card in
the expansion socket.
Make sure the goldĆstriped
bottom edge of the board
sits firmly in the expansion
slot socket and that the
bracket of the board is in
the corresponding groove.
ББББББББББ
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
ББББББББББ
Step 1.
Insert the card into the
computer chassis. While
firmly pressing down on
the card, use a
frontĆtoĆback rocking
motion to seat the card in
the expansion socket.
Make sure the goldĆstriped
bottom edge of the board
sits firmly in the expansion
slot socket and that the
bracket of the board is in
the corresponding groove.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 2.
Using a screwdriver,
secure the card with the
slot cover screw.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 2.
Using a screwdriver,
secure the card with the
slot cover's screw.
БББББББББББ
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
Б
БББББББББ
Б
БББББББББББ
Step 3.
Connect the ribbon cable
of the serial card to the
connector on the AutoMax
PC3000 Processor card.
ББББББББББ
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
Б
ББББББББ
Б
ББББББББББ
Step 3.
If you have an AutoMax
PC3000 Serial card
installed, connect the
ribbon cable of the Serial
card to the connector on
the AutoMax PC3000
Processor card.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 4.
Using a screwdriver,
replace the hold down
clamp.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 4.
Replace the computer
chassis' cover.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 5.
Close the chassis door,
and remount the chassis if
needed.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 5.
Reconnect the DCSĆNET
network and AĆB Remote
I/O cables.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 6.
Reconnect the DCSĆNET
network and AĆB Remote
I/O cables.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Step 6.
Plug in the power cord,
and turn on the computer.
БББББББББББ
Б
БББББББББ
Б
БББББББББББ
Step 7.
Reconnect the incoming
power line, and turn on the
AutoMax PC3000
Packaged Version.
ББББББББББ
Б
ББББББББ
Б
ББББББББББ
Once you apply power to the card, the following should occur:
D green OK light should be lit
D BATTERYSTATUS4@ variable should be true
If the Processor does not respond or the LEDs on the Serial card
show the code LO," you need to reload the operating system.
For more information, see the AutoMax Programming Executive
instruction manual. After reĆloading the operating system, you must:
D reset the network drop number
D reĆload your application tasks