KORG Electronic Keyboard - Manual (Page 811)

Chorus, Flanger, and Phaser 045: Bi Chorus
801
Source [Off…Tempo]
This selects a modulation source to modulate the tap
output levels (as set by Status, above) and the Tap 1
Feedback amount.
Amount [+/–100]
Sets the modulation amount for the Tap 1 Feedback.
Panning Preset [1: L 1 2 3 4 5 6 R, 2: L 135 246 R,
3: L 1 3 5 2 4 6 R, 4: L 1 4 5 6 3 2 R]
This selects combinations of stereo panning patterns
for the tap outputs.
LFO
Frequency [Hz] [0.02…13.00]
This sets the LFO speed, in Hz.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
045: Bi Chorus
This effect lets you place two independent
chorus/flanger units in series or in parallel. If placed in
series, feedback can be applied to the sound that has
passed through the two chorus modules, creating even
more complex modulation.
CHORUS1
Manual [0…100]
Sets the delay time for chorus 1.
LFO1 Depth [0…100]
Sets the LFO modulation depth for chorus 1.
Source [Off…Tempo]
Selects the modulation source that will control LFO
modulation depth.
Amount [+/–100]
Sets the amount by which the chorus 1 LFO
modulation depth will be controlled.
Feedback [0…100]
Sets the feedback amount for chorus 1.
CHORUS2
Manual [0…100]
Sets the delay time for chorus 2.
LFO2 Depth [0…100]
Sets the LFO modulation depth for chorus 2.
Amount [+/–100]
Sets the amount by which the chorus 2 LFO
modulation depth will be controlled.
Feedback [0…100]
Sets the feedback amount for chorus 2. When Routing
is set to Serial, this feeds back into Chorus 1, and
Chorus 1’s own Feedback setting is ignored.
LFO1/2
LFO1/2 Lock [Unlock, Lock-LFO1,
Lock-Common1, Lock-Common2]
This selects the LFO(s) used by the two choruses.
Unlock: LFO 1 and LFO 2 will operate independently.
Lock-LFO 1: both choruses will use LFO 1, with an
optional phase offset for LFO 2 (see “LFO2 Phase
[degrees],” below).
Lock-Common 1 or Lock Common 2: both choruses
will use the selected FX Common LFO, with an
optional phase offset for LFO 2.
LFO2 Phase [degrees] [–180…+180]
Sets the phase difference between LFO1 and LFO2,
when LFO 1/2 Lock is set to anything other than
Unlock.
LFO1 Frequency [Hz] [0.02…20.00]
Sets the LFO 1 speed. This applies only if LFO 1/2 Lock
is set to Unlock or Lock-LFO1.
LFO2 Frequency [Hz] [0.02…20.00]
Sets the LFO 2 speed. This applies only if LFO 1/2 Lock
is set to Unlock.
Source [Off…Tempo]
Selects a source to modulate the speeds of LFO1 & 2.
LFO1 Amount [–20.00…+20.00]
This sets the LFO1 Frequency modulation amount, in
Hz.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Right
Wet / Dry
Wet / Dry
Chorus
Chorus
Phase Lock
+
Mode
Feedback
Output Level1
Output Level2
Feedback
+
LFO2
LFO1
Serial
Dual
Output Mode
LFO 1/2 Lock / LFO2 Phase
LFO 1/2 Lock: Unlock
Chorus1
Chorus2
LFO1
LFO2
LFO 1/2 Lock: Lock - LFO1
LFO2 Phase
Chorus1
Chorus2
LFO1
LFO 1/2 Lock: Lock - Common2
Common FX LFO2
LFO2 Phase
Chorus1
Chorus2
LFO 1/2 Lock: Lock - Common1
Common FX LFO1
LFO2 Phase
Chorus1
Chorus2