KORG Electronic Keyboard - Manual (Page 809)

Chorus, Flanger, and Phaser 043: Multitap Cho/Delay 4Taps
799
MODULATION
L Pre Delay [msec] [0.0…50.0]
Sets the delay time for the left channel. p.797.
R Pre Delay [msec] [0.0…50.0]
Sets the delay time for the right channel. p.797.
Depth1 [0…100]
Sets the depth of LFO1 modulation.
Depth2 [0…100]
Sets the depth of LFO2 modulation.
Source [Off…Tempo]
Selects the modulation source of LFO1&2 modulation
depth.
Amount1 [+/–100]
Sets the modulation amount of LFO1 modulation
depth.
Amount2 [+/–100]
Sets the modulation amount of LFO2 modulation
depth.
Feedback [+/–100]
Sets the feedback amount. p.798.
High Damp [%] [0…100]
Sets the damping amount in the high range.
LFO1/2
LFO1 Waveform [Triangle, Sine]
Selects the waveform for LFO1.
LFO2 Waveform [Triangle, Sine]
Selects the waveform for LFO2.
Phase Sw [0 degree, 180 degree]
This lets you invert the LFO phase between the left and
right channels.
LFO1 Frequency [Hz] [0.02…30.00]
This sets the speed of LFO1, in Hz.
LFO2 Frequency [Hz] [0.02…30.00]
This sets the speed of LFO2, in Hz.
Source [Off…Tempo]
Selects a source to modulate the speeds of LFO1 & 2.
LFO1 Amount [–30.00…+30.00]
This sets the LFO1 Frequency modulation amount, in
Hz.
LFO2 Amount [–30.00…+30.00]
This sets the LFO2 Frequency modulation amount, in
Hz.
LFO1 Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO1, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
LFO2 Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO2, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
043: Multitap Cho/Delay 4Taps
This effect has four chorus blocks, each with a different
LFO phase. You can create a complex stereo image by
setting each block’s delay time, depth, output level,
and pan individually. You can also fix some of the
chorus blocks to combine the chorus and delay effects.
LFO1
LFO2
Bi-Phase Modulation LFO
Depth1
Depth2
+
Left
Right
Feedback Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
+ Level
Level
Level
Level
Pan
Pan
Pan
Pan
LFO: Triangle
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
0 [degree]
180 [degree]
90 [degree]
270 [degree]