KORG Electronic Keyboard - Manual (Page 507)

Sequencer P7: KARMA 7–1: GE Setup/Key Zones
497
Btm (Key Zone Bottom) [C–1…G9]
Top (Key Zone Top) [C–1…G9]
Please see “Key Zones” on page 376.
Note: In Sequencer mode, MIDI data for each KARMA
Module is transmitted and received on the “Input
Channel” and “Output Channel” (7–1c) that you
specify for each Module.
Transpose
Thru In Z (Thru In Zone) [Off, On]
Trans (Transpose In Zone) [–36…+36]
Thru Out Z (Thru Out Zone) [Off, On]
Trans (Transpose Out Zone) [–36…+36]
Please see “Key Zones” on page 376.
7–1c: MIDI I/O
Specifies the MIDI input/output channels for the four
KARMA Modules used by a Sequencer mode song.
Note: These settings make it possible to use multiple
KARMA Modules, and simultaneously play multiple
tracks of different MIDI channels. If you wish to real-
time record such a performance, use multi-track
recording setup (Sequencer 0–1a: Multi REC).
Input Channel [01…16, Tch]
Specifies the MIDI input channel for each KARMA
Module.
MIDI data from the keyboard or from MIDI IN that
matches the specified MIDI channel will be input to the
KARMA Module. (See the diagram below, “KARMA-
MIDI Input/Output Channel.”)
Tch: Automatically match the MIDI channel
(Sequencer 2–1a) of the track selected by Track Select
(Sequencer 0–1a).
Tch Also [Off, On]
This specifies whether the MIDI channel of the MIDI
track selected in Track Select will be used for MIDI
input in addition to the MIDI channel specified by
“Input Channel.”
Off (unchecked): Only the MIDI channel specified by
“Input Channel” will be used as the MIDI input
channel for the KARMA Module.
On (checked): The MIDI channel specified by “Input
Channel” and the MIDI channel of the MIDI track
selected by Track Select will be used as the MIDI input
channels for the KARMA Module.
If you check “Tch Also,” you will also be able to control
the KARMA function from the keyboard (transmitted
on the MIDI channel of the MIDI track selected by
Track Select).
Note: If you’ve selected Master Track or Audio Track
for Track Select, the MIDI channel of the MIDI track
shown in “Selected Track Info:” will be used.
Not available if the Module’s “Input Channel” is
Tch or the same MIDI channel as the MIDI track
selected for Track Select.
Output Channel [01…16, Tch]
Specifies the MIDI output channel for each KARMA
Module.
The MIDI data from each KARMA Module will be
transmitted on the MIDI output channel specified for
that KARMA Module, and will be sounded by tracks
with matching channels. For real-time recording, data
will be recorded on tracks with matching channels.
(See the diagram below, “KARMA-MIDI
Input/Output Channel.”)
Tch: Automatically match the MIDI channel
(Sequencer 2–1a) of the track selected by Track Select
(Sequencer 0–1a).
Example 1
With the following settings, switching Track Select
(the track you play) to change programs will also
switch to a different KARMA Module at the same time,
causing a different phrase to play. (See the diagram
“Example 1,” below.)
1. Set MIDI Track 1 as follows.
“Program Select”: a Guitar category program
MIDI Channel: 01
2. Set MIDI Track 2 as follows.
KARMA - MIDI Input / Output Channel
MIDI IN
Track Select = Track01
16ch
01ch Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
02ch
03ch
04ch
05ch
06ch
01ch
KARMA ON/OFF = ON
KARMA Module [A] In : 01ch Out : 01ch
KARMA Module [B] In : 01ch Out : 02ch
KARMA Module [C] In : 01ch Out : 03ch
KARMA Module [D] In : 16ch Out : 04ch