KORG Electronic Keyboard - Manual (Page 329)

PolysixEX Tone Adjust Common Tone Adjust parameters
319
PolysixEX Tone Adjust
PolysixEX Tone Adjust Default Settings
Tone Adjust provides an elegant physical interface to
the PolysixEX’s parameters. Most of the factory sounds
use the default layout, as shown above. You can also
customize the layout for individual sounds, if desired.
For more information about Tone Adjust, please see
“0–9f: Tone Adjust,” on page 26.
Common Tone Adjust parameters
These parameters affect both EXi 1 and 2. Except as
noted below, the Common Tone Adjust parameters
behave as described under “Common Tone Adjust
Parameters,” on page 28.
Amp Velocity Intensity. (–99…+99)
Not supported.
Filter/Amp EG Attack Time.
(–99…+99, CC#73)
This scales the attack time of the PolysixEX EG. It
interacts with CC# 73.
Filter/Amp EG Decay Time.
(–99…+99, CC#75)
This scales the decay time of the PolysixEX EG. It
interacts with CC# 75.
Filter/Amp EG Sustain Level.
(–99…+99, CC#70)
This scales the sustain level of the PolysixEX EG. It
interacts with CC# 70.
Filter/Amp EG Release Time.
(–99…+99, CC#72)
This scales the release time of the PolysixEX EG. It
interacts with CC# 72.
Filter EG, Amp EG, and Pitch EG Attack Time, Decay
Time, Sustain Level, Release Time are not supported
by the PolysixEX.
Pitch LFO1 Intensity. (–99…+99, CC#77)
This scales the VIBRATO INT parameter.
PolysixEX Tone Adjust parameters
In addition to the Common Tone Adjust parameters
listed above, the PolysixEX adds a number of its own
parameters.
Note that these additional parameters are separate for
each EXi, as opposed to being shared by both EXi in
the Program.
All of the additional parameters are listed below. Tone
Adjust parameters may affect the internal parameters
in one of two ways: they may be Relative, in which
case they scale the existing parameter value, or
Absolute, in which case they over-write the existing
value. Unless otherwise noted, all of the PolysixEX
parameters are Absolute.
The full name of the currently selected parameter is
shown in the status line at the top of the Control
Surface page, as well as in the popup menu. Some
parameters with longer names may show an
abbreviation for the slider, knob, and switch labels.
Filter
Kbd Track
Filter
Kbd Track
VCO
Octave
VCO
Octave
Filter EG
Intensity
Filter EG
Intensity
Filter
Cutoff
Filter
Cutoff
VCA
Mode
VCA
Mode
Filter
Resonance
Filter
Resonance
VCO
Waveform
VCO
Waveform
PWM
Speed
PWM
Speed
PW/
PWM
PW/
PWM
EG1
Decay
EG1
Decay
EG1
Attack
EG1
Attack
MG
Mode
MG
Mode
Effect
Int/Speed
Effect
Int/Speed
MG
Freq/Times
MG
Freq/Times
MG
Level
MG
Level
EG1
Release
EG1
Release
EG1
Sustain
EG1
Sustain
Effect
Mode
Effect
Mode
Switches 7 & 8:
LFOs 1 & 2 Stop Switches 7 & 8:
LFOs 1 & 2 Stop
Switches 15 & 16:
MG Tempo & Key Sync Switches 15 & 16:
MG Tempo & Key Sync Switches 9 & 10:
Arp Tempo & Key Sync Switches 9 & 10:
Arp Tempo & Key Sync