Rotary switch – Wavetronix Click 400 (900 MHz radio) (CLK-400) - User Guide User Manual
Page 67
66
CHAPTER 4 • CLICK 104
able to configure all other parameters (besides channel input mapping) using the front
panel menu and Click Supervisor.
Note
If any non-switch setting—that is, those that aren’t set by the rotary switch—has
been set using both the front panel menu and Click Supervisor, whichever configura-
tion was set most recently will take precedence.
Rotary Switch
The rotary switch is located on the lower part of the faceplate and can be used to change
the channel input mapping. Remember that if you use this switch to set the channel input
mapping, you won’t be able to use the software or the front panel menu to change this
particular parameter (although you will still be able to use them to change other param-
eters).
Channel input mapping is the process of telling the device which incoming data channels
should be mapped to which outgoing channels. As mentioned earlier, the Click 104 receives
serial datagrams from a sensor to which it is connected. These datagrams can contain many
channels of detection data. Because the devices have fewer output channels than there are
possible input datagram channels received from the sensor, you must use the channel input
map to map the desired inputs to outputs. The Click 104 has four output channels; if you
need more than this, you’ll need to use multiple devices daisy-chained together.
As shown in the table below, the outputs are mapped sequentially—that is, they can only
be mapped in numerically ordered groups of four (1–4, 5–8, etc.). If you set the switch to
3, for 9–12, then input 9 would be mapped to output 1, input 10 would be mapped to out-
put 2, input 11 would be mapped to output 3, and input 12 would be mapped to output 4.
Switch
Channels
0
Software mode
1
1–4
2
5–8
3
9–12
4
13–16
5
17–20
6
21–24
7
25–28
8
29–32
- Click 421 (bluetooth to serial converter) (CLK-421) - User Guide Click 342 (lean managed ethernet switch) (CLK-342) - User Guide Click 341 (lean managed ethernet switch) (CLK-341) - User Guide Click 340 (lean managed ethernet switch) (CLK-340) - User Guide Click 331 (unmanaged ethernet switch) (CLK-331) - User Guide Click 330 (unmanaged ethernet switch) (CLK-330) - User Guide Click 304 (RS-232 to RS-485 converter) (CLK-304) - User Guide Click 305 (RS-232 to RS-485 converter) (CLK-305) - User Guide Click 301 (serial to ethernet converter) (CLK-301) - User Guide Click 100 (16 output contact closure) (CLK-100) - User Guide Click 104 (4-channel DIN rail contact closure) (CLK-104) - User Guide Click 110 (4-channel contact closure eurocard) (CLK-110) - User Guide Click 112 (detector rack card) (CLK-112) - User Guide Click 114 (detector rack card) (CLK-114) - User Guide Click 120 (screw terminal relay) (CLK-120) - User Guide Click 121 (spring cage relay) (CLK-121) - User Guide Click 200 (surge suppression) (CLK-200) - User Guide Click 201 (1 amp AC to DC converter) (CLK-201) - User Guide Click 202 (2 amp AC to DC converter) (CLK-202) - User Guide Click 203 (UPS and battery) (CLK-203) - User Guide Click 204 (4 amp AC to DC converter) (CLK-204) - User Guide Click 210 (AC circuit breaker) (CLK-210) - User Guide Click 211 (AC outlet) (CLK-211) - User Guide Click 221 (DC surge protector) (CLK-221) - User Guide Click 222 (system surge protector) (CLK-222) - User Guide Click 223 (dual-485 surge protector) (CLK-223) - User Guide Click 230 (AC surge protector) (CLK-230) - User Guide Click 250 (wireless surge protector) (CLK-250) - User Guide