On-device configuration, Configuration features, Autobaud (green solid) – Wavetronix Click 400 (900 MHz radio) (CLK-400) - User Guide User Manual
Page 210
CHAPTER 24 • CLICK 304 209
Configuration Features
The faceplate of the Click 304 has the following three LEDs:
˽
PWR (red) lights up when the device has power.
˽
TD (yellow) lights up when the device is transmitting data.
˽
RD (green) lights up when the device is receiving data.
The LEDs are also used to indicate operation modes, which will be discussed in the On-
device Configuration section of this chapter.
The front also has a push-button labeled Mode Switch, which is used to cycle the Click 304
through operation modes. This will be discussed in the On-device Configuration section
of this chapter.
On-device Configuration
The Click 304 can be configured using the push-button on the lower part of the faceplate.
Press and hold the push-button to cycle through the different operation modes; release the
button when the desired mode is reached. A quick press and release of the push-button will
exit out of any mode and return the unit back to normal operation. Table 24.1 and the fol-
lowing sections describe the different operating modes.
Mode
LED
Definition
Autobaud
Green (solid)
To autobaud the Click 304, press the push-button, then
release when the green LED turns on.
Reset
Red (flashing)
To reset the Click 304 to factory defaults, press the push-
button, then release when the red LED is blinking.
Table 24.1 – Click 304 Operation Mode Definitions
Autobaud (green solid)
The Autobaud mode is used to match baud rates with an external device. By default, the
device will attempt to match baud rates with a SmartSensor on the bus; however, the device
can be configured to autobaud with any device that supports a serial interface.
While the device is autobauding, the green LED will be on while the red LED blinks. The
autobaud was successful if the red LED stays on and the green LED turns off. If the auto-
baud is not successful after a few minutes of trying, the red and green LEDs will stay on
indefinitely. In the case of a failed autobaud, push the push-button once to return the device
to its normal state.
- Click 421 (bluetooth to serial converter) (CLK-421) - User Guide Click 342 (lean managed ethernet switch) (CLK-342) - User Guide Click 341 (lean managed ethernet switch) (CLK-341) - User Guide Click 340 (lean managed ethernet switch) (CLK-340) - User Guide Click 331 (unmanaged ethernet switch) (CLK-331) - User Guide Click 330 (unmanaged ethernet switch) (CLK-330) - User Guide Click 304 (RS-232 to RS-485 converter) (CLK-304) - User Guide Click 305 (RS-232 to RS-485 converter) (CLK-305) - User Guide Click 301 (serial to ethernet converter) (CLK-301) - User Guide Click 100 (16 output contact closure) (CLK-100) - User Guide Click 104 (4-channel DIN rail contact closure) (CLK-104) - User Guide Click 110 (4-channel contact closure eurocard) (CLK-110) - User Guide Click 112 (detector rack card) (CLK-112) - User Guide Click 114 (detector rack card) (CLK-114) - User Guide Click 120 (screw terminal relay) (CLK-120) - User Guide Click 121 (spring cage relay) (CLK-121) - User Guide Click 200 (surge suppression) (CLK-200) - User Guide Click 201 (1 amp AC to DC converter) (CLK-201) - User Guide Click 202 (2 amp AC to DC converter) (CLK-202) - User Guide Click 203 (UPS and battery) (CLK-203) - User Guide Click 204 (4 amp AC to DC converter) (CLK-204) - User Guide Click 210 (AC circuit breaker) (CLK-210) - User Guide Click 211 (AC outlet) (CLK-211) - User Guide Click 221 (DC surge protector) (CLK-221) - User Guide Click 222 (system surge protector) (CLK-222) - User Guide Click 223 (dual-485 surge protector) (CLK-223) - User Guide Click 230 (AC surge protector) (CLK-230) - User Guide Click 250 (wireless surge protector) (CLK-250) - User Guide