Comtech EF Data CDM-IP 300L User Manual
Page 146
CDM-IP 300L IP-Centric Satellite Modem
Rev. 1
CD/CDMIP300L.IOM
120
Bulk Consol.
Status
(continued)
Parameter
Number
Parameter Name
(Command Reference)
Description
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 4)
(Note 4)
(Note 4)
(Note 4)
(Note 5)
(Note 6)
(Note 5)
(Note 6)
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
Demodulator Spectrum Rotation
(ref. 'DSR_' command).
Reed-Solomon Encoder Enable
(ref. 'RSEN_' command).
Reed-Solomon Decoder Enable
(ref. 'RSDE_' command).
Backward Alarm enable TX1
(ref. 'BW_TX1_' command).
Backward Alarm enable TX2
(ref. 'BW_TX2_' command).
Backward Alarm enable
(ref. 'BW_TX3_' command).
Backward Alarm enable TX4
(ref. 'BW_TX4_' command).
Backward Alarm enable RX1
(ref. 'BW_RX1_' command).
Backward Alarm enable RX2
(ref. 'BW_RX2_' command).
Backward Alarm enable RX3
(ref. 'BW_RX3_' command).
Backward Alarm enable RX4
(ref. 'BW_RX4_' command).
TX Driver Type
(ref. 'TXDR_' command).
RX Driver Type
(ref. 'RXDR_' command).
reserved null field.
ASYNC TX Overhead Baud Rate
(ref. 'TOBR_' command).
ASYNC RX Overhead Baud Rate
(ref. 'ROBR_' command).
ASYNC TX Channel Char. Length
(ref. 'TCCL_' command).
ASYNC RX Channel Char. Length
(ref. 'RCCL_' command).
p71 = n, where 'n' is '0' (NRM), '1' (INV).
p72 = n, where 'n' is '0' (off) or '1' (on).
p73 = n, where 'n' is '0'(OFF), '1' (ON), '2' (CORR_OFF).
p74 = n, where 'n' is '0' (off) or '1' (on).
p75 = n, where 'n' is '0' (off) or '1' (on).
p76 = n, where 'n' is '0' (off) or '1' (on).
p77 = n, where 'n' is '0' (off) or '1' (on).
p78 = n, where 'n' is '0' (off) or '1' (on).
p79 = n, where 'n' is '0' (off) or '1' (on).
p80 = n, where 'n' is '0' (off) or '1' (on).
p81 = n, where 'n' is '0' (off) or '1' (on).
p82 = n, where 'n' is '0' (G.703), '1' (V.35), '2' (RS422), or '3'
(RS232).
p83 = n, where 'n' is '0' (G.703), '1' (V.35), '2' (RS422), or '3'
(RS232).
p85 = nnnnn, where 'nnnnn' is the currently programmed baud
rate.
p86 = nnnnn, where 'nnnnn' is the currently programmed baud
rate.
p87 = n, where 'n' is the currently programmed character length.
p88 = n, where 'n' is the currently programmed character length.