KORG TRITON STUDIO music workstation - Manual (Page 70)

60
A/B/C/D KeyZone Bottom [C–1...G9]
Specifies the bottom key (lower limit) of the key zone.
A/B/C/D KeyZone Top [C–1...G9]
Specifies the top key (upper limit) of the key zone.
These parameters can also be set by holding down the
[Enter] key and playing a note.
■ 6.1–3b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c)
“Copy KARMA Module” (PROG 6.1–1c)
“Init KARMA Module” (6.1–1c)
“Select by Category” (1.1–4d)
6.1–4: Key T
(Key Thru)
☞ p.27 PROG 6.1–2b: Key Z/Thru
6.1–4a: Thru In Zone, Transpose InZ, Thru Out
Zone, Transpose OutZ
A/B/C/D Thru In Zone [Off, On]
A/B/C/D Transpose InZ [–36...+36]
A/B/C/D Thru Out Zone [Off, On]
A/B/C/D Transpose OutZ [–36...+36]
☞ p.27 PROG 6.1–2b: Key Z/Thru
■ 6.1–4b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c)
“Copy KARMA Module” (PROG 6.1–1c)
“Init KARMA Module” (6.1–1d)
“Select by Category” (1.1–4d)
6.1–5: RxFltr
(Receive Filter)
For each KARMA module ([A]–[D]), specify whether to fil-
ter the MIDI control data received by the module.
☞ p.28 PROG 6.1–3a: Rx Filter
6.1–5a: Rx Filter
A/B/C/D AfterT (After Touch) [Off, On]
A/B/C/D Bend (Pitch Bend) [Off, On]
A/B/C/D Damper (Damper CC#64) [Off, On]
A/B/C/D JS+Y (JS+Y CC#01) [Off, On]
A/B/C/D JS-Y (JS-Y CC#02) [Off, On]
A/B/C/D Other CC [Off, On]
☞ p.28 PROG 6.1–3a: Rx Filter
■ 6.1–5b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c)
“Copy KARMA Module” (PROG 6.1–1c)
“Init KARMA Module” (6.1–1d)
“Select by Category” (1.1–4d)
6.1–6: TxFltr
(Transmit Filter)
For each KARMA module ([A]–[D]), specify whether to fil-
ter the MIDI control data generated by the GE selected for
the module.
☞ p.28 PROG 6.1–4a: Tx Filter
6.1–6a: Tx Filter
A/B/C/D GE Bend (GE Pitch Bend) [Off, On]
☞ p.28 PROG 6.1–4a: Tx Filter
If the KARMA function is on and a KARMA module is
generating pitch bend data, the Bend Range (3.1–3a) of
the timbre will be controlled as follows.
The pitch bend range specified within the KARMA GE
will be transmitted from the KARMA module so that
the corresponding timbre will be forcibly set to this
bend range. This ensures that the pitch bend data gen-
erated by the KARMA module’s GE will function as
intended. At this time, pitch bender data produced by
operating the joystick will automatically be adjusted to
produce the same bend effect as when KARMA is off
(in most cases). (If multiple timbres are being controlled
by one KARMA module, the settings of the lowest-
numbered timbre will be used.)
6.1–4a
6.1–4b
6.1–5a
6.1–5b
6.1–6a
6.1–6b