KORG TRITON STUDIO music workstation - Manual (Page 260)

250
• In Combination and Sequencer modes, transmission/
reception of these messages can be turned on/off
independently for each timbre/track (“SW1/2” COMBI
4.4–1a, SEQ 4.4–1/2a)
Foot switch (CC#82) [Bn, 52, vv]
If the above CC# is assigned as the function of the ASSIGN-
ABLE SWITCH, operating the switch will transmit this mes-
sage with vv=127 [7F] for ON, and vv=00 [00] for OFF. (This
can also be set as a B mode function of the REALTIME CON-
TROL knobs [1]–[4].)
• In Combination and Sequencer modes, transmission/
reception of this message can be turned on/off
independently for each timbre/track (“Foot Pedal/
Switch” COMBI 4.4–2a, SEQ 4.4–3/4a).
When “Foot controller (CC#04)”–”Foot switch (CC#82)” are
operated on this instrument, the specified alternate modula-
tion or dynamic modulation etc. will be controlled. When
these messages are received, the result will be the same as if
the controller had been operated. For “SW1 modulation
(CC#80)”–”Foot switch (CC#82),” vv of 63 [3F] or less will be
OFF, and 64 [3F] or greater will be ON.
Damper pedal (CC#64) [Bn, 40, vv]
This message is transmitted when you operate a damper
pedal (separately sold Korg DS-1H etc.) connected to the
DAMPER jack, and the damper effect will be turned on/off.
If the DS-1H is used, a half-damper effect can be applied.
• In Combination and Sequencer modes, transmission/
reception of this message can be turned on/off
independently for each timbre/track (“Damper
CC#64” COMBI 4.1–2a, SEQ 4.1–3/4a).
Sostenuto (CC#66) [Bn, 42, vv]
If the above CC# is assigned as the function of the ASSIGN-
ABLE SWITCH, operating the switch will transmit this mes-
sage with vv=127 [7F] for ON, and vv=00 [00] for OFF, and
the sostenuto effect will be turned on/off. When this mes-
sage is received, the result will be the same as when the con-
troller is operated (OFF for vv=63 [3F] or below, and ON for
vv=64 [40] or above).
Soft pedal (CC#67) [Bn, 43, vv]
If the above CC# is assigned as the function of the ASSIGN-
ABLE SWITCH, the soft pedal effect will be turned on/off.
When this message is received, the result will be the same as
when the controller is operated.
Controlling via the controllers of a connected MIDI
instrument such as the TRITON
Ribbon Controller (CC#16) [Bn, 10, vv]
When a control change is received from the ribbon controller
or other assigned controller of a MIDI instrument (such as
the TRITON), the specified effect (e.g., alternate modulation
or dynamic modulation) will be applied.
• In Combination or Sequencer modes, transmission and
reception can be turned on/off for each timbre/track.
(“Ribbon CC#16” COMBI 4.2–2a, SEQ 4.2–3/4a)
Controlling the tone/envelope of a program
CC#70–78 control specific parameters of a program. For
details on the program parameters that correspond to each
control change, and how this instrument will respond in
each mode when these are received, refer to “This instru-
ment operations when control changes are transmitted/
received” (
☞p.242).
Low pass filter cutoff (CC#74) [Bn, 4A, vv]
Resonance level/High pass filter cutoff (CC#71) [Bn, 47, vv]
Filter EG intensity (CC#79) [Bn, 4F, vv]
Release time (CC#72) [Bn, 48, vv]
These messages are transmitted when you operate this
instrument’s REALTIME CONTROLS [1]–[4] knobs in A
mode. (They can also be set as B mode functions.)
Sustain level (CC#70) [Bn, 46, vv]
Attack time (CC#73) [Bn, 49, vv]
Decay time (CC#75) [Bn, 4B, vv]
LFO 1 speed (CC#76) [Bn, 4C, vv]
LFO 1 depth (pitch) (CC#77) [Bn, 4D, vv]
LFO 1 delay (CC#78) [Bn, 4E, vv]
These messages are transmitted when assign the above CC#
to the REALTIME CONTROLS [1]–[4] knobs in B mode and
operate them.
When you operate these, the corresponding program
parameters will be controlled, and the sound and envelope
will change. When these messages are received, the result
will be the same as when the controller is operated. (When
the message has a value vv=64 [40], the setting will have the
value that was set by the program parameter.)
• In Combination and Sequencer modes, transmission/
reception can be turned on/off independently for each
timbre/track (“Realtime Control Knob1, 2, 3, 4”
COMBI 4.3–1a, SEQ 4.3).
In Program mode, the corresponding program parame-
ters will be temporarily edited by these messages. You
can Write the program to save the modified state
(except for certain parameters). The Write operation can
also be performed by a MIDI exclusive Program Write
Request message, in addition to the usual method of
using this instrument’s switches. When you write the
data, the values of the corresponding program parame-
ters will be rewritten.
The results of receiving these messages will depend on
the instrument. The operation may be different when a
device other than this instrument is connected.
Controlling the KARMA function
When you operate the KARMA REALTIME CONTROLS
knobs or switches of this instrument with the following
CC#’s assigned, the assigned CC# will be transmitted, and at
the same time this instrument itself will also be controlled.
When these messages are received, the result will be the
same as if the built-in controller had been operated.
Assignments of a CC# to each knob or key can be made in
GLOBAL mode 6.1–2(2): KARMA 1 (2) pages. Normally you
will leave this Off. Make these settings only when you need
to assign MIDI control change messages; for example when
you wish to record KARMA REALTIME CONTROLS knob
or key operations into the internal sequencer or an external
MIDI sequencer, or when you wish to control the KARMA
function from an external MIDI device.
Although it is possible to set each knob and key to any MIDI
control change message CC#00–95, you should normally use
the utility menu command “Reset KARMA Ctrls Assign,”
and select “Default Setting.” (
☞p.146)
The operations shown below are for the “Default Setting.”
These will be transmitted when you operate the correspond-
ing controller of the KARMA workstation. When these are
received, the result will be the same as if the built-in control-
ler had been operated.
KARMA ON/OFF (CC#14) [Bn, 0E, vv]
This corresponds to the KARMA Realtime Controls [ON/
OFF] key. Transmit vv=127 [7F] when on, and vv=127 [7F]
when off.