KORG TRITON STUDIO music workstation - Manual (Page 121)

7.1
7.2
7.3
1.1
1.2
2.1
2.2
2.3
3.1
3.2
3.3
3.4
4.1
4.2
4.3
4.4
5.1
5.2
6.1
6.2
6.3
6.4
SEQ
111
6.4–4(5)b: UTILITY
☞ “Memory Status,” “Solo Selected Track,” “Rename Song,”
“Delete Song,” “Copy From Song,” “Copy From Combi,”
“FF/REW Speed,” “Set Location,” (1.1–1d)
“Copy KARMA Module” (PROG 6.1–1c)
“Init KARMA Module” (COMBI 6.1–1d)
6.4–6: Rndm1
(Random 1)
6.4–7: Rndm2
(Random 2)
6.4–6(7)a: Rhythm, Duration, Index, Cluster, Veloc-
ity, CC–A/B, Drum
Rhythm (Rhythm Seed) [1, 2, 3, 4]
Duration (Duration Seed) [1, 2, 3, 4]
Index (Index Seed) [1, 2, 3, 4]
Cluster (Cluster Seed) [1, 2, 3, 4]
Velocity (Velocity Seed) [1, 2, 3, 4]
CC–A/B (CC–A/B Seed) [1, 2, 3, 4]
Drum (Drum Seed) [1, 2, 3, 4]
☞ p.64 COMBI 6.4–6(7)a: Rndm 1/2
■ 6.4–6(7)b: UTILITY
☞ “Memory Status,” “Solo Selected Track,” “Rename Song,”
“Delete Song,” “Copy From Song,” “Copy From Combi,”
“FF/REW Speed,” “Set Location,” (1.1–1d)
“Copy KARMA Module” (PROG 6.1–1c), “Select by Cate-
gory” (PROG 3.1–3b)
“Init KARMA Module” (COMBI 6.1–1d)
Specifies the bus to which the program oscillator(s) of each
track 1–8, 9–16 will be sent. You can also set the amount of
signal that will be sent to the master effects.
☞ For details on insert effects, refer to “7. Effect Guide”
p.159.
7.1–1: BUS..8
(BUS T01...08)
7.1–2: BUS..16
(BUS T09...16)
7.1–1(2)a: BUS Select, Send1(MFX1), Send2(MFX2)
BUS Select [DKit, L/R, IFX1...5, 1, 2, 1/2, Off]
Specifies the output bus for the program oscillators of tracks
1–8 and 9–16.
The state of the settings can be viewed in the Route page.
(
☞ COMBI 7.1–1a)
S1 (Send1(MFX1)) [000...127]
S2 (Send2(MFX2)) [000...127]
Here you can adjust the send levels from tracks 1–8, 9–16 to
master effects 1 and 2. This is valid when “BUS Select” is set
either to L/R or Off. If IFX 1, 2, 3, 4, or 5 is selected, the send
level to the master effects 1 and 2 is set by the “Send 1” and
“Send 2” parameters located in the Insert FX tab, after the
signal passes through IFX 1–5.
These settings have no effect if “BUS Select” is set to 1, 2 or
1/2
.
The send 1 and 2 settings you make here will be used when
the song is played or recorded from the beginning. If you
change the settings while recording, the change will be
recorded as part of the musical data, and the send amount
will change when the data is played back. You can also
change these settings during playback. However if send 1
and 2 data has been recorded, the settings will change
accordingly.
If “Status” (3.1–1(2)a) is either INT or BTH, CC#93 and
#91 can be received to control send 1 and 2 respectively
and change their settings. When you switch songs or
return to the beginning of a song, tracks whose “Status”
is EXT, EX2 or BTH will transmit these settings via
MIDI. This data will be transmitted on the MIDI chan-
nel of each track as set by “MIDI Channel” (3.1–1(2)a).
The actual send level is determined by multiplying the
value of these parameters with the send level settings of
the oscillator(s) of the program used by the track (“S1
(Send1(MFX1))” and “S2 (Send2(MFX2))” PROG 7.2–
1a).
6.4–6b
6.4–6a
6.4–7b
6.4–7a
SEQ 7.1: BUS
7.1–1a
7.1–1b