St.vibrato (stereo vibrato), St.biphasemod(stereo biphase modulation), St.biphasemod – KORG TRITON STUDIO music workstation User Manual
Page 192: St.vibrato, Stereo biphase modulation), Stereo vibrato)
182
026: St.BiphaseMod
(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog-type, unstable
modulated sound.
027: St.Vibrato
(Stereo Vibrato)
This effect causes the pitch of the input signal to shimmer.
Using the AutoFade allows you to increase or decrease the
shimmering speed.
b: LFO Freq Mod, f: AUTOFADE Src, g: Fade Rate, g: Dly
When “LFO Freq Mod” is set to AUTOFADE, you can use the
modulation source selected in “AUTO FADE Src” as a trigger to
automatically fade in the modulation amount. When “BPM/MIDI
Sync” is set to On, you cannot use this.
The “Fade Rate” parameter specifies the rate of fade-in. The “Dly”
parameter determines the time from AutoFade modulation source
ON until the fade-in starts.
The following is an example of fade-in where the LFO speed is
increased from “1.0Hz” to “4.0Hz” when a note-on message is
received.
a
LFO1 Wave (LFO1 Waveform)
Selects LFO1 waveform
Triangle, Sine
b
LFO2 Wave (LFO2 Waveform)
Selects LFO2 waveform
Triangle, Sine
c
LFO Phase Sw
0, 180degree
Switches the LFO phase difference between left and right
d
F1 (LFO1 Frequency)
Sets the LFO1 speed
0.02...30.00Hz
(Source)
Selects the modulation source of LFO1&2 speed
Off...Tempo
(Amount)
Sets the modulation amount of LFO1 speed
–30.00...+30.00
e
F2 (LFO2 Frequency)
Sets the LFO2 speed
0.02...30.00Hz
(Amount)
Sets the modulation amount of LFO2 speed
–30.00...+30.00
f
L Dly (L Pre Delay)
Sets the delay time for the left channel
0.0...50.0ms
☞
Fx:016
R Dly (R Pre Delay)
Sets the delay time for the right channel
0.0...50.0ms
☞
Fx:016
g
Depth1
Sets the depth of LFO1 modulation
0...100
(Source)
Off...Tempo
Selects the modulation source of LFO1&2 modulation depth
(Amount)
–100...+100
Sets the modulation amount of LFO1 modulation depth
h
Depth2
Sets the depth of LFO2 modulation
0...100
(Amount)
–100...+100
Sets the modulation amount of LFO2 modulation depth
i
Feedback
Sets the feedback amount
–100...+100
☞
Fx:017
HiDamp (High Damp)
Sets the damping amount in the high range
0...100%
j
W/D (Wet/Dly)
–Wet...–1:99, Dry, 1:99...Wet
Sets the balance between the effect and dry sounds
☞
Fx:010,
(Source)
Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
Chorus/Flanger
Left
Right
Feedback
180 [degree]
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
LFO1: Tri / Sine
LFO2: Tri / Sine
Chorus/Flanger
High Damp
LFO1
LFO2
Bi-Phase Modulation LFO
Depth1
Depth2
+
a
LFO Wave (LFO Waveform)
Selects LFO Waveform
Triangle, Sine
Shape (LFO Shape)
–100...+100
Determines how much the LFO waveform is changed
☞
Fx:020
b
LFO Freq Mod (LFO Frequency Mod)
Dmod, AUTOFADE
Switches between Dmod and AUTOFADE for the LFO frequency
modulation
☞
c
Freq (LFO Frequency)
0.02...20.00Hz
Sets the LFO speed
☞
Fx:009,
(Source)
Selects the modulation source of LFO speed
Off...Tempo
(Amount)
–20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync
Off, On
Switches between using the frequency of the LFO speed and using
the tempo and notes
☞
Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
☞
Fx:009
Base (Base Note)
Selects the type of notes that specify the LFO speed
☞
Fx:009
Times
1...16
Sets the number of notes that specify the LFO speed
☞
Fx:009
e
Depth
Sets the depth of LFO modulation
0...100
(Source)
Off...Tempo
Selects the modulation source of the LFO modulation depth
(Amount)
–100...+100
Sets the modulation amount of the LFO modulation depth
f
AUTOFADE Src (AUTOFADE Source)
Off...Tempo
Selects the modulation source that starts AutoFade
☞
,
g
Fade Rate (Fade-In Rate)
Sets the rate of fade-in
1...100
☞
Dly (Fade-In Delay)
Sets the fade-in delay time
00...2000ms
☞
h
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source)
Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
Vibrato
Vibrato
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO: Tri / Sine
LFO Shape
Fade-In Delay
LFO Frequency
AutoFade