KORG TRITON STUDIO music workstation - Manual (Page 244)

234
Dynamic MIDI Sources
The sources (Dynamic MIDI Sources) are organized into the
following groups
JS +Y #01...JS X: Controller group
Short Note...Black Note: Note group
Velocity...Vel Out Z: Velocity Group
Depending on the combination of source and destination
(Dynamic MIDI Destinations), the selected destination may
not function as you intend. Refer to the explanations of com-
bining sources and destinations in each section of “Dynamic
MIDI Destinations,” and make sure to select sources and
destinations that are appropriate for each other.
For JS+Y #01...JS X , you can specify the range of control val-
ues in “Range-Btm/Top” (6.4–3a/b/c/d). Control values
within this range will be the source.
Off
No source will be selected.
JS+Y #01
The +Y direction (away from yourself) of the joystick
(CC#01) will be the source.
For JS+Y #01...JS X , you can specify the range of control val-
ues in “Range-Btm/Top” (6.4–3a/b/c/d). Control values
within this range will be the source.
JS-Y #02
The –Y direction (toward yourself) of the joystick (CC#02)
will be the source.
Pedal #04
The assignable foot pedal (CC#04) will be the source.
The function of the assignable pedal connected to the
ASSIGNABLE PEDAL jack must be assigned as Foot Pedal
(CC#04)
for the GLOBAL 6.1: Controller Foot page “Foot
Pedal Assign” parameter.
Damper #64
The damper pedal will be the source.
Prta.SW #65
The portamento switch (CC#65) will be the source.
FootSW #82
The assignable foot switch (CC#82) will be the source.
The function of the assignable foot switch connected to the
ASSIGNABLE SWITCH jack must be assigned as Foot
Switch (CC#82)
for the GLOBAL 6.1: Controller Foot page
“Foot SW Assign” parameter.
MIDI CC#83
MIDI control change CC#83 will be the source.
Ribbon #16
MIDI control change CC#16. The ribbon controller of a con-
nected TRITON etc. will be the source.
K.Knob1...8
The corresponding KARMA Realtime Controls knob [1]–[8]
will be the source.
If a MIDI control change is assigned in the GLOBAL
6.1: Controller KARMA1 page, this will be controlled
by reception of the assigned MIDI control change.
K.SW1/K.SW2
The KARMA Realtime Controls switch [1] or [2] will be the
source.
If a MIDI control change is assigned in the GLOBAL
6.1: Controller KARMA1 page, this will be controlled
by reception of the assigned MIDI control change.
KARM OnOff
The KARMA Realtime Controls [ON/OFF] key will be the
source.
If a MIDI control change is assigned in the GLOBAL
6.1: Controller KARMA1 page, this will be controlled
by reception of the assigned MIDI control change.
AfterT
Aftertouch (channel aftertouch) will be the source.
JS X
The X (horizontal) direction of the joystick will be the
source.
For JS X, “Pol” (6.4–3a/bc/d) allows you to select +/– or
–/+
in addition to the usual + or – operations.
When the controller is moved all the way to the left or right,
the value will change as follows. The example shown below
is for when Tempo is selected as the destination. (Original
tempo is =100 BPM, “Range-Btm/Top”: 000/127)
+:
Far left (+/–0) → far right (maximum)
100 BPM → 200 BPM
–: Far left (+/–0) → far right (maximum negative)
100 BPM → 50 BPM
+/–: Far left (maximum negative) → center (+/–0) → far
right (maximum)
50 BPM
→ 100 BPM → 200 BPM
–/+: Far left (maximum) → center (+/–0) → far right
(maximum negative)
200 BPM
→ 100 BPM → 50 BPM
Short Note
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the range
of note numbers. Only notes within the specified range with
a duration of less than 45 ms between note-on and note-off
will be the source.
000: C-1...012: C0...024: C1...036: C2...
045: C3...060: C4...072: C5...084: C6...
096: C7...108: C8...120: C9...127: G9
Note
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the range
of note numbers. Notes within the specified range will be
the source. (
☞Short Note)
Dynamic MIDI Sources & Desti-
nations