KORG TRITON STUDIO music workstation - Manual (Page 199)

Ef
fect
189
037: Detune
Using this effect, you can obtain a detune effect that offsets
the pitch of the effect sound slightly from the pitch of the
input signal. Compared to the chorus effect, a more natural
sound thickness will be created.
e: InLvl Mod, e: Src
This parameter sets the dynamic modulation of the input level.
038: Pitch Shifter
This effect changes the pitch of the input signal. You can select
from three types: Fast (quick response), Medium, and Slow
(preserves tonal quality). You can also create an effect in
which the pitch is gradually raised (or dropped) using the
delay with feedback.
a: Mode
This parameter switches the pitch shifter operating mode. With
Slow
, tonal quality will not be changed too much. With Fast, the
effect becomes a Pitch Shifter that has a quick response, but may
change the tone. Medium is in between these two. If you do not
need to set too much pitch shift amount, set this parameter to
Slow
. If you wish to change the pitch significantly, use Fast.
b: Shift, b: (Source), b: (Amount), c: Fine, c: (Amount)
The amount of pitch shift will use the value of the “Shift” plus the
“Fine” value. The amount of modulation will use the c: (Amount)
value plus d: “(Amount).”
Modulation Source is used both for “Shift” and “Fine.”
e: Feedback Position, f: Feedback
When “Feedback Position” is set to Pre, the pitch shifter output is
again input to the pitch shifter. Therefore, if you specify a higher
value for the Feedback parameter, the pitch will be raised (or low-
ered) more and more each time feedback is repeated.
If “Feedback Position” is set to Post, the feedback signal will not
pass through the pitch shifter again. Even if you specify a higher
value for the Feedback parameter, the pitch-shifted sound will be
repeated at the same pitch.
a
Sft (Pitch Shift)
Sets the pitch difference from the input signal –100...+100cent
(Source)
Selects the modulation source of the pitch shift Off...Tempo
(Amount)
Sets the modulation amount of the pitch shift –100...+100cent
b
Delay (Delay Time)
Sets the delay time 0...1000ms
c
Feedback
Sets the feedback amount –100...+100
d
High Damp
Sets the damping amount in the high range 0...100%
e
InLvl Mod (Input Level Dmod [%])
Sets the modulation amount of the input level –100...+100
☞
,
Src (Source)
Selects the modulation source for the input level Off...Tempo
☞
f
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Detune
Input Level
Louder
Max Zero
Higher
D -mod
Input Level
Max Zero
Higher
D -mod
x1.0
x0.5
Amt= +100
Amt= +50
Louder
x1.0
x0.5
Amt= –100
Amt= –50
Input Level D-mod
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre
Post
a
Mode Slow, Medium, Fast
Switches Pitch Shifter mode
☞
b
Shift (Pitch Shift) –24...+24
Sets the pitch shift amount by steps of a semitone
☞
,
(Source) Off...Tempo
Selects the modulation source of pitch shift amount
☞
(Amount)
Sets the modulation amount of pitch shift amount –24...+24
☞
c
Fine
Sets the pitch shift amount by steps of a cent –100...+100cent
☞
,
(Amount)
Sets the modulation amount of pitch shift amount –100...+100cent
☞
d
Delay (Delay Time)
Sets the delay time 0...1000ms
e
Feedback Position
Switches the feedback connection. Pre, Post
☞
f
Feedback
Sets the feedback amount –100...+100
☞
HiDamp (High Damp)
Sets the damping amount in the high range 0...100%
g
InLvl Mod (Input Level Dmod [%]) –100...+100
Sets the modulation amount of the input level
☞
Fx:037,
Src (Source)
Selects the modulation source for the input level Off...Tempo
☞
Fx:037
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100