KORG TRITON STUDIO music workstation - Manual (Page 212)

202
064: Comp–AmpSim
(Compressor – Amp Simulation)
This effect combines a mono-type compressor and an amp
simulation. You can change the order of the effect connection.
065: Comp–OD/HG
(Compressor – Overdrive/Hi.Gain)
This effect combines a mono-type compressor and an over-
drive/high-gain distortion. You can change the order of the
effect connection.
066: Comp–P4EQ
(Compressor – Parametric 4-Band EQ)
This effect combines a mono-type compressor and a four-
band parametric equalizer. You can change the order of the
effect connection.
a
[CMP] Sensitivity
Sets the sensitivity 1...100
☞
Fx:002
b
Attack
Sets the attack level 1...100
☞
Fx:002
Level (Output Level)
Sets the compressor output level 0...100
☞
Fx:002
c
Pre EQ Trim
Sets the EQ input level 0...100
d
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ –15...+15dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ –15...+15dB
e
[AMP] Amplifier Type
Selects the type of guitar amplifier SS, EL84, 6L6
f
[Routing] CMP
→
AMP, AMP → CMP
Switches the order of the compressor and amp simulation connec-
tion
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
a
[CMP] Sensitivity
Sets the sensitivity 1...100
☞
Fx:002
b
Attack
Sets the attack level 1...100
☞
Fx:002
Level (Output Level)
Sets the compressor output level 0...100
☞
Fx:002
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Compressor
Routing
Amp Simulation
Amp Simulation Filter
LEQ HEQ EQ Trim
Output Level
Envelope - Control
Comp
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Overdrive / Hi-Gain
3 Band PEQ
Output Level
Mode: Overdrive / Hi-Gain
Drive
Driver
Compressor
Output Level
Envelope - Control
Comp
c
[OD] Mode (Drive Mode) OverD, Hi-Gain
Switches between overdrive and high-gain distortion
Drive
Sets the degree of distortion 1...100
☞
Fx:006
d
Level (Output Level) 0...50
Sets the overdrive output level
☞
Fx:006,
(Source) Off...Tempo
Selects the modulation source for the overdrive output level
(Amount) –50...+50
Sets the modulation amount of the overdrive output level
e
Lo (Low Cutoff) 20...1.00kHz
Sets the center frequency for Low EQ (shelving type)
G (Gain)
Sets the gain of Low EQ –18...+18dB
f
M1 (Mid1 Cutoff) 300...10.00kHz
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
Sets the band width of Mid/High EQ 1 0.5...10.0
☞
Fx:006
G (Gain)
Sets the gain of Mid/High EQ 1 –18...+18dB
g
M2 (Mid2 Cutoff) 500...20.00kHz
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
Sets the band width of Mid/High EQ 2 0.5...10.0
☞
Fx:006
G (Gain)
Sets the gain of Mid/High EQ 2 –18...+18dB
h
[Routing] CMP → OD, OD → CMP
Switches the order of the compressor and overdrive connection
i
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
a
[CMP] Sensitivity
Sets the sensitivity 1...100
☞
Fx:002
b
Attack
Sets the attack level 1...100
☞
Fx:002
Level (Output Level)
Sets the compressor output level 0...100
☞
Fx:002
c
[PEQ] Trim
Sets the parametric EQ input level 0...100
d
[Routing] CMP → PEQ, PEQ → CMP
Switches the order of the compressor and parametric EQ connection
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Trim
Parametric 4Band EQ
Output Level
Envelope - Control
Comp