KORG TRITON STUDIO music workstation - Manual (Page 36)

26
Here you can make KARMA function settings for use by the
program. In Program mode you can use one KARMA mod-
ule (module [A]).
When you switch programs, these settings will automati-
cally be rewritten to the KARMA settings stored in that pro-
gram. (
☞ GLOBAL 1.1–1c: System Basic, Auto KARMA
“Program”: On)
The KARMA function can be turned on/off by the KARMA
real-time controls [ON/OFF] key.
The state of the KARMA real-time controls [LATCH]
[SCENE] keys, switches [1]/[2], and knobs [1]–[8], and the
note settings/velocity of the CHORD TRIGGER [1]–[4] keys
can be saved in each program.
In order for these settings to be valid, GLOBAL 1.1–1c:
System Basic, Auto KARMA “Program” must be On.
The PROG 6.1–1: Setup page parameters can also be set
from the PROG 1.1–3: KARMA page.
6.1–1: Setup
Here you can select the GE used by the KARMA module,
and make key zone and MIDI filter settings for the KARMA
module.
6.1–1a: (Tempo)
Specifies the tempo at which the KARMA function will
operate. (
☞ p.3)
6.1–1b: GE Setup
GE Category [00: name ...]
This displays the category of the currently selected GE.
(
☞ p.5)
GE Select [0000: Arp Model 1 Up/Dn…]
Indicates the GE. ( ☞ p.3)
Init K.RTC (KARMA Real-time Controls–Use GE’s Value)
[Off, On]
Specifies whether the settings of the KARMA real-time con-
trols knobs [1]–[8] and switches [1]/[2] will be initialized
when you select a GE.
This allows you to hear the original state of the phrase or
pattern produced by the GE. Normally you will turn this On
when selecting a GE. (
☞ p.5)
■ 6.1–1c: UTILITY
☞ “Write Program” (1.1–1c), “Select by Category” (1.1–3b)
For details on how to select the desired utility, refer to
“PROG 1.1–1c: UTILITY.”
Copy KARMA Module
This command copies the settings of the KARMA module
used by a specified program, combination, song, or song
play.
The “Input Channel” and “Output Channel” (6.2–1a)
settings of combination, song, or song play will not be
copied.
1 Select “Copy KARMA Module” to access the dialog box.
2 In “From,” select the copy source mode, bank, and num-
ber.
You can press a Bank [A]–[G] key to select the bank.
3 If the copy source is a combination, song, or song play,
you can also select the module that will be copied.
4 If you wish to copy KARMA RT parameters and
KARMA real-time CONTROLS settings as well, check
“KARMA RT&Panel Setting.”
Settings copied by “KARMA RT&Panel Setting”
• [ON/OFF] key setting
• [LATCH] key setting
• CHORD TRIGGER [1]–[4] key settings
• SCENE [1], [2] key settings
• KARMA real-time CONTROLS knobs [1]–[8],
switches [1]/[2] settings
• PROG 6.4: Ed-KARMA RT settings (RTParm,
DynMIDI, Name)
5 To execute the copy, press the [F8] (“OK”) key. To cancel
without executing press the [F7] (“Cancel”) key.
Init KARMA Module (Initialize KARMA Module)
This command initializes the settings of the KARMA module.
The GE selection will not be initialized. The GE param-
eter “Values” will be set to the default values that are
preset for the selected GE.
1 Select “Init KARMA Module” to access the dialog box.
2 If you also wish to initialize the KARMA RT parameters
and KARMA real-time Controls settings, check
“KARMA RT&Panel Setting.”
Settings that are initialized by “KARMA RT&Panel
Setting”
• 6.4: Ed-KARMA RT settings (RTParm, DynMIDI,
Name)
• KARMA real-time Controls knobs [1]–[8], switches
[1]/[2], [SCENE] key, [LATCH] key settings
• CHORD TRIGGER [1]–[4] key settings
3 To initialize the settings, press the [F8] (“OK”) key. To
cancel without initializing, press the [F7] (“Cancel”) key.
PROG 6.1: Ed–KARMA
6.1–1a
6.1–1b
6.1–1c