KORG TRITON STUDIO music workstation - Manual (Page 215)

Ef
fect
205
071: Limit–Cho/Fl
(Limiter – Chorus/Flanger)
This effect combines a mono-type limiter and a chorus/
flanger. You can change the order of the effect connection.
072: Limit–Phaser
This effect combines a mono-type limiter and a phaser. You
can change the order of the effect connection.
a
[LMT] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞
Fx:003
b
Threshld (Threshold) –40...0dB
Sets the level above which the compressor is applied
☞
Fx:003
G.Adj (Gain Adjust)
Sets the limiter output gain –Inf, –38...+24dB
☞
Fx:003
c
Attack
Sets the attack time 1...100
☞
Fx:003
Release
Sets the release time 1...100
☞
Fx:003
d
[CH/FL] LFO (LFO Waveform)
Selects the LFO waveform of the chorus/flanger Tri, Sine
F (LFO Frequency)
Sets the LFO speed 0.02...20.00Hz
e
Dly (Delay Time)
Sets the delay time 0.0...50.0ms
Dep (Depth)
Sets the depth of LFO modulation 0...100
Feedback
Sets the feedback amount –100...+100
☞
Fx:020
f
[F] EQ Trim
Sets the EQ input level 0...100
g
[F] Pre LEQ Gain [dB]
Sets the gain of Low EQ –15...+15dB
Pre HEQ Gain [dB]
Sets the gain of High EQ –15...+15dB
h
[F] Cho/Flng W/D –Wet...–2:98, Dry, 2:98...Wet
Sets the effect balance of the chorus/flanger
☞
Fx:010, 020
Output Mode Normal, Wet Inv
Selects the output mode for the chorus/flanger
☞
Fx:067
i
Routing LMT → CH/FL, CH/FL → LMT
Switches the order of the limiter and chorus/flanger connection
☞
Fx:067
j
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Chorus/Flanger
Feedback
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
Limiter
Limiter
Gain Adjust
Envelope - Control
LEQ HEQ EQ Trim
Chorus/Flanger
LFO: Tri / Sine
a
[LMT] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞
Fx:003
b
Threshld (Threshold) –40...0dB
Sets the level above which the compressor is applied
☞
Fx:003
G.Adj (Gain Adjust)
Sets the limiter output gain –Inf, –38...+24dB
☞
Fx:003
c
Attack
Sets the attack time 1...100
☞
Fx:003
Release
Sets the release time 1...100
☞
Fx:003
d
[PHS] LFO (LFO Waveform)
Selects the LFO waveform of the phaser Tri, Sine
F (LFO Frequency)
Sets the LFO speed 0.02...20.00Hz
e
Manu (Manual)
Sets the frequency to which the effect is applied 0...100
Dep (Depth)
Sets the depth of LFO modulation 0...100
Resonance
Sets the resonance amount –100...+100
☞
Fx:023
f
[P] Phaser W/D –Wet...–2:98, Dry, 2:98...Wet
Sets the phaser effect balance
☞
Fx:010, 023
Output Mode Normal, Wet Inv
Selects the phaser output mode
☞
Fx:067
g
Routing LMT → PHS, PHS → LMT
Switches the order of the limiter and phaser connection
☞
Fx:067
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Limiter
Gain Adjust
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+