KORG TRITON STUDIO music workstation - Manual (Page 170)

160
Sequencer mode
Song Play mode
*1 Some effects may not have these parameters.
1. In/Out
Insert Effects (IFX 1, 2, 3, 4, 5) have a stereo input and a ste-
reo output . If you select Dry (no effect) for the “W/D”
parameter, the stereo input signal will be output in stereo
without being processed by the effect. If you select Wet
(effect applied), the processed signal will be output in one of
the following ways:
If you select 000: No Effect, stereo input signals are output
in stereo without being processed.
The possible routing of effect inputs and outputs is indi-
cated in the upper left corner of the block diagram.
These can be switched on/off by the “On/Off” settings in
7.2: Ed-Insert FX, Setup pages IFX1–5 in each mode. When
off
, the effect will be bypassed. In the same way as for 000:
No Effect , the stereo input sound will be output in stereo
without modification.
Separately from this “On/Off” setting, MIDI control
change CC#92 can be received to turn all IFX1–5 effects
off. A value of 0 is off, and a value of 1–127 restores the
original setting. You can also use “FX SW” (GLOBAL
1.1–1b) to turn off IFX1–5 in the same way. This is con-
trolled on the global MIDI channel “MIDI Channel”
(GLOBAL 2.1–1a).
Double-size effects
Double-size effects 090–102 use twice the area of what
other effects use.
You can select them for Insert Effects IFX2, IFX3, and IFX4.
Note that if you select a double-size effect for IFX2, you can-
not use IFX3. In the same way, if you select a double-size
effect for IFX3 or IFX4, you cannot use IFX4 or IFX5 respec-
tively.
Selecting double-size effects for IFX2 and IFX4
Selecting a double-size effect for IFX3
2. Routing
You can use up to five channels (IFX 1, 2, 3, 4, and 5) for the
Insert Effects
in any mode.
2–1. Program mode
Use “BUS Select” (PROG 7.1–1a) to set the destination bus of
the oscillator output.
L/R:
The signal is not sent to the Insert Effects. Instead, it is
sent to AUDIO OUTPUT (MAIN) L/MONO and R after the
Master EQ.
IFX1–5:
The signal is sent to Insert Effects IFX 1, 2, 3, 4, 5.
1, 2, 1/2: The signal is sent to AUDIO OUTPUT (INDIVID-
UAL) 1, 2 ( ☞ p.166 “Individual Outputs”). The signal is not
sent to the Insert Effects, Master Effects, and or Master EQ.
Off:
The signal is not sent to AUDIO OUTPUT (MAIN L/
MONO, R, (INDIVIDUAL) 1 or 2. (After the Master Effects,
the signal is output to AUDIO OUTPUT (MAIN).) Select this
option if you connect the Insert Effects with the Master
Effects in series, with the send level specified by “MFX1
Send1”and “MFX2 Send2.”
Use MFX1 Send “Send1” and “Send2” (PROG 7.1–1a) to
specify the send level for the Master Effects. This setting is
effective if “BUS Select” (PROG 7.1–1a) is set to L/R or Off.
If “BUS Select” is set to IFX1–5, use “S1 (Send1(MFX1))” and
“S2 (Send2(MFX2))”(PROG 7.2–1) for the post-IFX signal
(
☞ “3. Mixer”).
Send Level 1 can be controlled by MIDI Control Change
CC#93, and Send Level 2 can be controlled by MIDI
Control Change CC#91. At this time, the actual send
level is determined by multiplying the Send Level 1 or 2
value of the oscillator with the Send Level 1 or 2 value
received via MIDI.
Input Volume (SEQ 1.1)
S1/2 (Send1/2) (SEQ 7.1)
Effect Trim parameter *1 (SEQ 7.2, 7.3)
Output Effect W/D parameter (SEQ 7.2, 7.3)
Rtn1/2 (Return1. 2) (SEQ 7.3)
Input Volume (S.PLAY 1.1)
S1/2 (Send1/2) (S.PLAY 7.1)
Effect Trim parameter *1 (S.PLAY 7.2, 7.3)
Output Effect W/D parameter (S.PLAY 7.2, 7.3)
Rtn1/2 (Return1. 2) (S.PLAY 7.3)
Insert Effects
(IFX 1, 2, 3, 4, 5)
Stereo In - Stereo Out
Mono In - Mono Out
Mono In - Stereo Out
Effect
Effect
Effect +
Effect +
Wet