KORG TRITON STUDIO music workstation - Manual (Page 188)

178
e: Hi/Lo Split
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
g: Feedback
Sets the feedback amount of the chorus block. Increasing the feed-
back will allow you to use the effect as a flanger.
018: MltTap ChoDly
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block’s
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
019: Ensemble
This Ensemble effect has three chorus blocks that use LFO to
create subtle shimmering, and gives three dimensional depth
and spread to the sound, because the signal is output from the
left, right, and center.
c: Shimmer
This parameter sets the amount of shimmering of the LFO wave-
form. Increasing this value adds more shimmering, making the
chorus effect more complex and richer.
a
LFO Freq (LFO Frequency)
Sets the LFO speed 0.02...13.00Hz
b
T1(000) (Tap1 Delay)
Sets the Tap1 (LFO phase=0 degrees) delay time 0...570ms
D (Depth)
Sets the Tap1 chorus depth 0...30
L (Level)
Sets the Tap1 output level 0...30
P (Pan) L6...L1, C, R1...R6
Sets the Tap1 stereo image
c
T2(180) (Tap2 Delay) 0...570ms
Sets the Tap2 (LFO phase=180 degrees) delay time
D (Depth)
Sets the Tap2 chorus depth 0...30
L (Level)
Sets the Tap2 output level 0...30
P (Pan) L6...L1, C, R1...R6
Sets the Tap2 stereo image
d
T3(090) (Tap3 Delay) 0…570ms
Sets the Tap3 (LFO phase=90 degrees) delay time
D (Depth)
Sets the Tap3 chorus depth 0...30
L (Level)
Sets the Tap3 output level 0...30
P (Pan) L6...L1, C, R1...R6
Sets the Tap3 stereo image
e
T4(270) (Tap4 Delay) 0...570ms
Sets the Tap4 (LFO phase=270 degrees) delay time
D (Depth)
Sets the Tap4 chorus depth 0...30
L (Level)
Sets the Tap4 output level 0...30
P (Pan) L6...L1, C, R1...R6
Sets the Tap4 stereo image
f
T1 Fb (Tap1 Feedback)
Sets the Tap1 feedback amount –100...+100
(Source) Off...Tempo
Selects the modulation source of Tap1 feedback amount and effect
balance
(Amount) –100...+100
Sets the Tap1 feedback amount and modulation amount
Left
Right
Feedback Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
+ Level
Level
Level
Level
Pan
Pan
Pan
Pan
LFO: Triangle
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
0 [degree]
180 [degree]
90 [degree]
270 [degree]
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Amount)
Sets the modulation amount of the effect balance –100...+100
a
Speed
Sets the LFO speed 1...100
(Source)
Selects the modulation source of LFO speed Off...Tempo
(Amount)
Sets the modulation amount of LFO speed –100...+100
b
Depth
Sets the depth of LFO modulation 0...100
(Source) Off...Tempo
Selects the modulation source of the LFO modulation depth
(Amount) –100...+100
Sets the modulation amount of the LFO modulation depth
c
Shimmer 0...100
Sets the amount of shimmering of the LFO waveform
☞
d
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
LFO
Shimmer
+ Ensemble
Time
Level
Ensemble LFO
Shimmer