KORG TRITON STUDIO music workstation - Manual (Page 148)

138
Convert Position [Pre MIDI, Post MIDI]
This setting specifies the location at which the Transpose,
Velocity Curve, and After Touch Curve settings will be
applied. This setting will affect the MIDI data that is trans-
mitted and received, and the data that is recorded on the
internal sequencer.
When using this instrument’s keyboard to play the internal
tone generator, the Transpose, Velocity Curve, and After
Touch Curve settings will always take effect regardless of
this setting.
Pre MIDI: Velocity Curve, After Touch Curve, and Trans-
pose will be applied to the data that is transmitted from this
instrument’s keyboard.
This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is transmitted
from MIDI OUT when this instrument’s keyboard is played,
and the data that is recorded on the internal sequencer. MIDI
data received from MIDI IN or the data played back by the
internal sequencer will not be affected.
Post MIDI: Velocity Curve, After Touch Curve, and Trans-
pose will be applied to data before it enters the tone genera-
tor.
This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is sent to the
internal tone generator when you play this instrument’s
keyboard, when the internal sequencer is played back, or
when data is received from MIDI IN.
This setting will not affect the data that is transmitted from
MIDI OUT or recorded on the internal sequencer when you
play this instrument’s keyboard or playback the sequencer.
2.1–1b: MIDI Filter
Enable Program Change [Off, On]
On (checked): Program changes will be transmitted and
received.
In Program mode (PROG 1.1: Play), the program will be
switched when a program change message is received on
the global MIDI channel specified by “MIDI Channel” (2.1–
1a). When you switch programs, a program change message
will be transmitted on the global MIDI channel.
In Combination mode (COMBI 1.1: Play), the combination
will be switched when a program change message is
received on the global MIDI channel. However, it is possible
to set the “Combi (Combi Change)” parameter so that the
combination is not switched. When a program change is
received on the channel specified for each timbre by “MIDI
Channel” (COMBI 3.1–1a), the program of that timbre will
be switched. However, the program changes for each timbre
will be affected by the setting of the “Program Change”
parameter (COMBI 4.1–1a).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
“Status” (COMBI 3.1–1a) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on
a channel that corresponds to a track whose “Status” (SEQ
3.1–1/2a) is set to INT or BTH will switch programs on that
track. When you select a song or playback sequencer data,
program changes will be transmitted on the channels of
tracks whose “Status” is set to BTH, EXT, or EX2.
Off (unchecked):
Program changes will not be transmitted
or received.
Bank (Bank Change) [Off, On]
On (checked): The Bank Select control change message will
be transmitted together with program change messages.
This is valid when “Enable Program Change” is checked.
Off (unchecked):
Bank Select messages will not be transmit-
ted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
Combi (Combi Change) [Off, On]
On (checked): When in COMBI 1.1: Play, an incoming pro-
gram change message on the global MIDI channel set by
“MIDI Channel” (2.1–1a) will switch combinations. This is
valid when “Enable Program Change” is checked. An
incoming program change on a channel other than the glo-
bal MIDI channel will switch the program of any timbre that
matches that MIDI channel.
Off (unchecked):
An incoming program change message on
the global MIDI channel will switch the program of any tim-
bre whose “MIDI Channel” (COMBI 3.1–1a) matches the
global MIDI channel. The combination will not be switched.
The program changes for each timbre will be affected by the
setting of the “Program Change” parameter (COMBI 4.1–
1a).
AfterT (After Touch) [Off, On]
On (checked): MIDI after touch messages will be transmit-
ted and received.
Off (unchecked):
MIDI after touch messages will neither be
transmitted nor received.
When recording sounds that do not require the use of after
touch, you can uncheck this parameter to save memory.
This setting has no effect when you use the internal
sequencer to playback sequence data that was recorded with
after touch data; i.e., after touch will be transmitted via MIDI.
This instrument’s keyboard transmits only channel after
touch; it does not transmit polyphonic after touch. However,
since this instrument does support polyphonic after touch as
an Alternate Modulation Source (AMS), it can receive poly-
phonic after touch to control individual notes.
Velocity
Curve
Aftertouch
Curve
Tone
generator
Note number
change
Play
MIDI IN
MIDI OUT
Record
Sequencer
Transpose Scale
Velocity
Curve
Aftertouch
Curve
Tone
generator
Play
MIDI IN
MIDI OUT
Record
Sequencer
Transpose Scale
Pitch change