KORG TRITON STUDIO music workstation - Manual (Page 202)

192
042: Auto Reverse
This effect records the input signal and automatically plays it
in reverse (the effect is similar to a tape reverse sound).
a: Rec Mode, b: Reverse Time
When ”Rec Mode“ is set to Single, you can set up to 1320msec for
“Reverse Time.” If recording starts during the reverse playback,
the playback will be interrupted.
When “Rec Mode” is set to Multi, you can make another record-
ing during the reverse playback. However, the maximum Reverse
Time is limited to 660msec.
If you wish to record a phrase or rhythm pattern, set “Rec Mode”
to Single. If you record only one note, set “Rec Mode” to Multi.
The “Reverse Time” parameter specifies the maximum duration
of the reverse playback. The part in excess of this limit will not be
played in reverse. If you wish to add short pieces of the reverse
playback of single notes, make the “Reverse Time” shorter.
c: Envelope, c: Src, d: Threshold
These parameters select the source to control the start and end of
recording.
When “Envelope” is set to Dmod, the input signal will be
recorded only when the value of the modulation source selected
by the Src parameter is 64 or higher.
When “Envelope” is set to Input, the input signal will be recorded
only when its level exceeds the Threshold level.
When recording is completed, reverse playback starts immedi-
ately.
043: LCR Delay
(L/C/R Delay)
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
e: HiDamp, e: LoDamp
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
a
Rec Mode
Sets the recording mode Single, Multi
☞
b
Reverse Time 20...1320ms
Sets the maximum duration of the reverse playback
☞
c
Envelope (Envelope Select) Dmod, Input
Selects whether the start and end of recording is controlled via the
modulation source or the input signal level
☞
,
Src (Source) Off...Tempo
Selects the modulation source that controls recording when Enve-
lope is set to Dmod
☞
d
Threshold 0...100
Sets the recording start level when Envelope is set to Input
☞
e
Response 0...100
Sets the speed of the response to the end of recording
☞
Fx:031
f
Direct Mix Always On, Always Off, Cross Fade
Selects how a dry sound is mixed
☞
Fx:031
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Input
D-mod
Envelope Select
D -mod
Envelope Control
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+ Auto Reverse
Direct
Mix
Rec/Reverse Play
Control
Rec Rec
Rec Mode/Reverse Time
Input
Rec Mode = Single
Rec Mode = Multi
Time
Reverse Time Reverse Time
Envelope Select = Input Reverse Reverse
a
L Delay (L Delay Time)
Sets the delay time of TapL 0...1360ms
Level
Sets the output level of TapL 0...50
b
C Delay (C Delay Time)
Sets the delay time of TapC 0...1360ms
Level
Sets the output level of TapC 0...50
c
R Delay (R Delay Time)
Sets the delay time of TapR 0...1360ms
Level
Sets the output level of TapR 0...50
d
C Fb (C Delay Feedback)
Sets the feedback amountof TapC –100...+100
(Source) Off...Tempo
Selects the modulation source of the TapC feedback amount
(Amount) –100...+100
Sets the modulation amount of the TapC feedback amount
e
HiDamp (High Damp)
Sets the damping amount in the high range 0...100%
☞
LoDamp (Low Damp)
Sets the damping amount in the low range 0...100%
☞
f
InLvl Mod (Input Level Dmod [%]) –100...+100
Sets the modulation amount of the input level
☞
Fx:037,
Src (Source)
Selects the modulation source for the input level Off...Tempo
☞
Fx:037
g
Spread 0...50
Sets the width of the stereo image of the effect sound
☞
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
C Delay
R Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level