KORG TRITON STUDIO music workstation - Manual (Page 127)

S.PLA
Y
1.1
2.2
2.3
3.1
4.1
4.2
6.1
6.2
6.3
6.4
7.1
7.2
7.3
117
1.1–2: Prog..8
(Program T01...08)
1.1–3: Prog..16
(Program T09...16)
Specifies the program used by each track.
1.1–2(3)a: ProgramSelect, PLAY/MUTE, SOLO On/
Off
Program Select
[A...F/000...127, G001...128 g001:1...g128: d]
Indicates the program used by each track.
F000–127 can be selected if the separately sold EXB-MOSS
option is installed.
When this parameter is selected, you can use the VALUE
controllers to make your selection. At this time, a BANK key
LED will light to indicate the bank of the selected program.
The track number and the abbreviation for the category of
the selected program will be displayed above “Program
Select.”
By holding down the [TIMBRE/TRACK] key and
pressing a [F1](T1/T9)–[F8](T8/T16) key you can move
to the corresponding track “T1”–”T16.”
The program bank can also be selected directly by using
the [A]–[G] keys.
You can also use the “Select by Category” utility to
select programs by category. (
☞ p.2)
If the track “Status” (3.1–1(2)a) is INT or BTH, MIDI
program changes can be received to select a program.
Tracks 1–16 are controlled by MIDI channels 1–16
respectively.
PLAY/MUTE [PLAY, MUTE]
This sets the play/mute status of each track.
PLAY: The track will play.
MUTE: The track will be muted.
SOLO ON/OFF [SOLO On, SOLO Off]
Switches the Solo function on/off.
Select the check box at the right of “PLAY/MUTE,” and turn
this setting on/off. A track for which this is on will show an
“S” character within the box, and only that track will sound.
The remaining tracks will be muted.
If a track muted by the Mute or Solo function has a
“Status” (3.1–(2)a) of EXT or BTH, the MIDI note-on/
off messages of that track will not be transmitted.
(However, the track selected by “Play (Track Select)”
(1.1–1a) is an exception.)
If the utility menu command “Solo Selected Track”
(1.1–1d) is ON, its solo settings will take priority (when
ON). When you press “SOLO On/Off” or press a
parameter of another track, only that track will be
soloed and will sound.
■ 1.1–2(3)c: UTILITY
☞ “GM Initialize” (1.1–1b), “Solo Selected Track,” “Load
Template Song,” “Save Template Song,” “Set Location”
(SEQ 1.1–1d)
Select by Category
You can select the program for each track by category. This
command will appear and can be selected if “Program
Select” is selected.
1.1–4: Mix..8
(Mixer T01...08)
1.1–5: Mix..16
(Mixer T09...16)
Here you can set the pan and volume of each track.
1.1–4(5)a: Pan, Volume
Pan (Panpot) [RND, L001...C064...R127]
Set the panning for each track (channel) 1–16 ( ☞ SEQ 1.1–
4(5)a).
Tracks whose “Status” (3.1–1(2)a) is INT or BTH can
receive MIDI control change (CC) #10 to control the
panpot. When receiving CC#10, a value of 0 or 1 will be
far left, 64 will be center, and 127 will be far right.
Tracks 1–16 will be controlled by MIDI channels 1–16
respectively.
1.1–2c
1.1–2a
1.1–2b
1.1–4a
1.1–4b