KORG TRITON STUDIO music workstation - Manual (Page 58)

48
1.1–5: K.RTC
(KARMA RTC)
1.1–5a: RT Knob/SW Name
This displays the name of the KARMA real-time Controls
knobs [1]–[8] and switches [1]/[2], and the knob or switch
settings that are written in the combination.
The [----] portion preceding the name of the knob or switch
shows the abbreviated name of the category of the program
sounded by the timbre that is played by the KARMA mod-
ule controlled by operations of knobs [1]–[8] and switches
[1]/[2]. If there are multiple timbres with programs of differ-
ing categories, this will indicate [MLTI].
The name can be selected in COMBI 6.4–4/5: Ed-KARMA
RT, Name1/2 page.
☞ p.6 PROG 1.1–4a: RT Knob/SW Name
■ 1.1–5b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre,” “Select by
Category” (1.1–1c)
1.1–6: Note
(Note Activity)
1.1–6a: Note Activity Display, Chord Name
Note Activity Display A, B, C, D
This is a real-time display of the note on/off status gener-
ated by each KARMA module (modules [A], [B], [C], and
[D]).
The key zone settings of the four KARMA modules are dis-
played as a solid line. (
☞ p.59 COMBI 6.1–3: Key Z)
Chord Name A, B, C, D
This shows the name of the chord detected by each KARMA
module.
Chord detection is affected by the key zone (COMBI
6.1-2a: Ed-KARMA Key Zone) and “Transpose”
(COMBI 6.2-1a: Module Parameter) of each KARMA
module, and by the “Dynamic MIDI Destination”
(COMBI 6.4-3a/b/c/d) “Chord Scan” and “Smart
Scan” settings.
■ 1.1–6b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre,” “Select by
Category” (1.1–1c)
2.1–1: Prog
(Timbre Program)
Indicates the bank and program for each timbre 1–8. These
parameters can also be set from the 1.1: Play, Prog page.
2.1–1a: Program Select, Program Name
Program Select
Indicates the program that will be used by each timbre.
(
☞ 1.1–2c)
Program Name
This displays part of the program name selected for each
timbre. (
☞ 1.1–2c)
■ 2.1–1b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c),
“Select by Category”: Select Program by Category (Tim-
bre) (1.1–2e)
2.1–2: Mix
(Mixer)
Specifies the pan and volume for each timbre 1–8. These
parameters can also be set from the 1.1: Play, Mixer page.
2.1–2a: Pan, Volume
Pan
Sets the pan of each timbre 1–8. ( ☞ 1.1–3a)
Volume
Sets the volume of each timbre 1–8. ( ☞ 1.1–3a)
■ 2.1–1b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c)
1.1–5a 1.1–5b
1.1–6b
1.1–6a
COMBI 2.1: Ed–Prog/Mixer
2.1–1a
2.1–1b
2.1–2a
2.1–2b