KORG TRITON STUDIO music workstation - Manual (Page 118)

108
Here you can set the KARMA module parameters. In
Sequencer mode, you can use four KARMA modules (mod-
ules [A], [B], [C], and [D]) just as in Combination mode. Use
the [F6] (
) key and [F7] ( ) key (6.2–1d) to select
the KARMA module that you wish to edit.
6.2–1: Parm1
(Parameter 1)
6.2–1a: Module Parameters
The selected KARMA module is indicated as [A], [B], [C], or
[D].
Transpose [–36...+36]
Force Range
[Off, Lowest, Highest, C3–B3[1], C3–B3[2]]
Delay Start [Off, Fixed, 3...4x ]
Delay Start Fixed [0000ms...5000ms]
Quantize Trig [Off, On]
☞ p.29 PROG 6.2–1a: Module Parameter, BG p.88 “About the
KARMA function — KARMA function synchronization”
TimbZ Bypass (TimbZone Bypass) [Off, On]
Specifies whether the key zone settings (3.3–1b) and velocity
zone settings (3.4–1(2)b) of the track will be applied to the
phrase or pattern generated by the KARMA module.
On (checked): The key zone settings and velocity zone set-
tings of the track will be bypassed for the phrase or pattern
generated by the KARMA module. The settings of the track
will be ignored, and the notes generated by the KARMA
module will be sounded.
Off (unchecked):
The key zone settings and velocity zone
settings of the track will be applied to the phrase or pattern
generated by the KARMA module. Notes generated by the
KARMA module will not sound if they are outside the key
zone or velocity zone of the track.
Root Position [Off, On]
☞ p.29 PROG 6.2–1a: Module Parameter
6.2–1b: Tx CC (Transmit CC)
☞ p.30 PROG 6.2–1b: Tx CC
This data will be transmitted on the “Output Channel” (6.1–
2a) of the KARMA module.
Tx CC1...4 Number [Off, 000...095]
☞ p.30 PROG 6.2–1b: Tx CC
If you turn on KARMA [ON/OFF] when a song for
which KARMA [ON/OFF] is on is selected, the speci-
fied MIDI control change message will be transmitted.
If the selected GE is generating the control change that
you specified here, the effect of the control change gen-
erated by the GE will take priority.
6.2–1c: Value (Tx CC Value)
Value (Tx CC1...4 Value) [000...127]
☞ p.30 PROG 6.2–1c: Value (Tx CC Value)
6.2–1d: ,
Use the [F6] ( ) key and [F7] ( ) key to select the
KARMA module that you wish to edit.
■ 6.2–1e: UTILITY
☞ “Memory Status,” “Solo Selected Track,” “Rename Song,”
“Delete Song,” “Copy From Song,” “Copy From Combi,”
“FF/REW Speed,” “Set Location,” (1.1–1d)
“Copy KARMA Module” (PROG 6.1–1c), “Select by Cate-
gory” (PROG 3.1–3b)
“Init KARMA Module” (COMBI 6.1–1d)
6.2–2: Parm2
(Parameter 2)
6.2–2a: Trigger/Latch
Specifies the trigger conditions and latch on/off settings for
the GE selected for each KARMA module [A]–[D].
Note:
Note Trigger
[Any, AKR, 1st, Dyn]
☞ p.31 PROG 6.2–2a: Trigger/Latch, “Note Trigger”
Note Latch [Off, On]
☞ p.31 PROG 6.2–2a: Trigger/Latch, “Note Latch”
In Sequencer mode, this can be turned on/off for each
KARMA module. KARMA modules for which this setting is
turned on will be in Latch On mode when the [LATCH] key
is on (LED lit).
☞ p.31 PROG 6.2–2a: Trigger/Latch, “Note Latch”
Env1:/Env2:/Env3:
Env1 Trigger/Env2 Trigger/Env3 Trigger
[Any, AKR, 1st, Dyn]
Env1 Latch/Env2 Latch/Env3 Latch
[Off, Sus1, Rel1, Sus2, Rel2]
☞ p.31 PROG 6.2–2a: Trigger/Latch.
SEQ 6.2: KARMA Mdl
6.2–1a 6.2–1e 6.2–1d 6.2–1b 6.2–1c
6.2–2a
6.2–2d 6.2–2b 6.2–2c