KORG TRITON STUDIO music workstation - Manual (Page 200)

190
039: PitchShft Mod
(Pitch Shift Modulation)
This effect modulates the detuned pitch shift amount using an
LFO, adding a clear spread and width to the sound by pan-
ning the effect sound and dry sound to the left and right. This
is especially effective when the effect sound and dry sound
output from stereo speakers are mixed.
a: Pitch Shift [cent], e: Depth
These parameters set the amount of pitch shift and amount of
modulation by means of the LFO.
f: Pan, g: W/D
The Pan parameter pans the effect sound and dry sound to the left
and right. With L, the effect sound is panned left, and the dry
sound is panned right. With a W/D = Wet setting, the effect and
dry sound will be output in a proportion of 1:1.
040: Rotary SP
(Rotary Speaker)
This effect simulates a rotary speaker, and obtains a more real-
istic sound by simulating the rotor in the low range and the
horn in the high range separately. The effect also simulates the
stereo microphone settings.
a: (Sw)
This parameter sets how the modulation source switches between
rotation and stop.
When “Sw” = Tggl (Toggle), the speaker rotates or stops alter-
nately each time you press the pedal or operate the joystick.
Each time the value for the modulation source exceeds 64,
the speaker rotates or stops alternately.
When “(Sw)” = Mmnt (Moment), the speaker is rotating. It stops
a
Pitch Shift
Sets the pitch difference from the input signal –100...+100cent
☞
b
LFO Wave (LFO Waveform)
Selects LFO Waveform Triangle, Square
c
Freq (LFO Frequency) 0.02...20.00Hz
Sets the LFO speed
☞
Fx:009,
(Source)
Selects the modulation source of LFO speed Off...Tempo
(Amount) –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using
the tempo and notes
☞
Fx:009,
BPM
Selects MIDI Clock and assigns tempo MIDI, 40...240
☞
Fx:009
Base (Base Note)
Selects the type of notes that specify the LFO speed
☞
Fx:009
Times 1...16
Sets the number of notes that specify the LFO speed
☞
Fx:009
e
Depth –100...+100
Sets the LFO modulation depth for pitch shift amount
☞
,
(Source) Off...Tempo
Selects the modulation source of the depth of modulation
(Amount) –100...+100
Sets the modulation amount of the depth of modulation
f
Pan L, 1:99...99:1, R
Sets the panning effect sound and dry sound separately
☞
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
☞
,
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
LFO: Tri / Sqr
Pitch Shifter
Pan
+
Pitch
Higher
Pitch Shift Mod - Pitch Shift / Depth
Lower
Original Pitch
Pitch Shift (+ value)
LFO Waveform=Triangle
Depth (+value)
LFO Waveform=Square
Depth (–value)
a
Mode (Mode Switch)
Switches between speaker rotation and stop Rotate, Stop
(Source) Off...Tempo
Selects the modulation source that toggles between rotation and
stop
(Sw) Tggl, Mmnt
Selects switching mode of the modulation source that toggles
between rotation and stop
☞
b
Speed (Speed Switch) Slow, Fast
Switches the speaker rotation speed between slow and fast
(Source) Off...Tempo
Selects the modulation source that toggles between slow and fast
(Sw) Tggl, Mmnt
Selects switching mode of the modulation source that toggles
between slow and fast
☞
c
H/R.Bal (Horn/Rotor Balance) Rot, 1...99, Hrn
Sets the level balance between the high-range horn and low-range
rotor
ManuSp (Manual Speed Control) Off...Tempo
Selects the modulation source in case the rotation speed is changed
directly
☞
,
d
Horn Accel (Horn Acceleration) 0...100
How quickly the horn rotation speed in the high range is switched
☞
Ratio (Horn Ratio) Stop, 0.50...2.00
Adjusts the (high-range side) horn rotation speed. Standard value is
1.00. Selecting “Stop” will stop the rotation
e
Rotor Accel (Rotor Acceleration) 0...100
Determines how quickly the rotor rotation speed in the low range is
switched
☞
Ratio (Rotor Ratio) Stop, 0.50...2.00
Adjusts the (low-range side) rotor rotation speed. Standard value is
1.00. Selecting “Stop” will stop the rotation
f
MicDistance 0...100
Sets the distance between the microphone and rotary speaker
☞
Spread (Mic Spread)
Sets the angle of left and right microphones 0...100
☞
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
D -mod
D -mod
D -mod
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
Speaker Simulation
Mic Distance
Mic Spread
Horn/Rotor
Balance
Horn
Rotary Speaker
Rotor
+