N 2.1–1c: utility – KORG TRITON STUDIO music workstation User Manual
Page 149
1.1
2.1
3.1
4.1
5.1
6.1
GLOBAL
139
Ctrl Change (Control Change)
[Off, On]
On (checked):
Control change messages will be transmitted
and received.
Off (unchecked):
Control change messages will neither be
transmitted nor received.
This setting has no effect when you use the internal
sequencer to playback sequence data that was recorded with
control change data; i.e., control changes will be transmitted
via MIDI.
Exclusive
[Off, On]
On (checked):
System exclusive data will be transmitted
and received. Check this setting when you wish to use a
connected computer etc. to edit this instrument, or vice
versa.
Off (unchecked):
System exclusive data will neither be
transmitted nor received. Normally you will leave this
unchecked.
However, system exclusive data will be transmitted and
received while the page menu commands (““Dump Pro-
gram”–”Dump All”) of this page are displayed.
■
2.1–1c: UTILITY
☞
“Write Global Setting” (1.1–1d)
Dump Program
Dump Combination
Dump Drum Kit
Dump Global Setting
Dump Sequencer
Dump All
These commands allow this instrument’s data to be trans-
mitted to another connected KARMA, MIDI data fil.er, or
computer in the form of system exclusive data.
Selects the data to be dumped from the Utility menu (see the
table below) to access the dialog box.
As necessary, select the bank and number of the data to be
dumped, and press [F8] (“OK”) key.
Transmission
Do not touch this instrument’s switches or turn off the
power while data is being transmitted.
Data dump transmission procedure
1
Connect this instrument to the device that will receive
the data dump.
If you are using a computer that is able to receive MIDI
exclusive data, connect the computer’s MIDI interface
(connected to the computer) to the MIDI OUT connector
of this instrument. (
If you are using a MIDI data filter etc., connect this
instrument’s MIDI OUT connector to the MIDI IN con-
nector of the MIDI data filter.
2
Select Global mode 2.1: MIDI.
3
In the Utility menu, select the data that you wish to
dump.
If you wish to dump data for an individual bank, set
“Program” to Bank, and specify the bank number below
it. If you wish to dump data for an individual program,
set “Program” to Single, and specify the program num-
ber below it.
4
Press the [F8] (“OK”) key to transmit the data.
While the data is being transmitted, the display will indi-
cate “Now transmitting data.”
The data size and the time required for transmission will
depend on the type of data.
For the size and the time required to dump each type of
data, refer to the table below.
When you save data dumps from this instrument to a
MIDI data filer, do not save multiple data dumps
together. If this data is saved together, there will be
insufficient time for this instrument to write each
received portion into memory before the next portion of
data arrives, so that it will be impossible to receive all of
the data correctly.
Dump Program
Programs of all banks, programs of the
specified bank, one program
Dump Combination
Combinations of all banks, combinations of
the specified bank, one combination
Dump Drum Kit
All drum kits, One drum kit
Dump Global
Global settings (except for the Drum Kits of
Global mode)
Dump Sequencer
All sequences
Dump All
All banks of programs + combinations +
drum kits + global settings + sequences
Type of data dumped
Data size (kByte)
Time required (Sec)
This
instru-
ment
EXB-
MOSS is
installed
This
instru-
ment
EXB-
MOSS is
installed
Program All
588.1
715.0
188.2
228.8
Program Bank (A...E)
117.6
---
37.6
---
Program Bank (F)
---
127.0
---
40.6
Program Single (A...E)
0.9
---
0.3
---
Program Single (F)
---
1.0
---
0.3
Combination All
874.2
←
279.7
←
Combination Bank
145.7
←
46.6
←
Combination Single
1.1
←
0.4
←
Drum Kit All
300.8
←
96.2
←
Drum Kit Single
4.7
←
1.5
←
Global Setting
1.0
←
0.3
←
Sequence Data
5.6–
1376.6
←
1.8–
440.5
←
All
1769.7–
3140.7
1896.6–
3267.6
566.2–
1004.9
606.8–
1045.5