1–5c: time mod. (time modulation), N 4.1–5d: utility – KORG TRITON STUDIO music workstation User Manual
Page 29
PROG
1.1
2.1
2.2
2.3
3.1
4.1
4.2
5.1
5.2
5.3
6.1
6.2
6.3
6.4
7.1
7.2
7.3
19
S (AMS SW Start)
[–, 0, +]
Specifies the direction in which “AMS (Level Mod. AMS)”
will affect “S (Start Level).” When “I (AMS Intensity)” has a
positive (+)
value, a setting of + for this parameter will
allow “AMS” to raise the EG level, and a setting of – will
allow “AMS” to lower the EG level. With a setting of 0 there
will be no change.
A (AMS SW Attack)
[–, 0, +]
Specifies the direction in which “AMS (Level Mod. AMS)”
will affect “A(Attack Level).” When “I (AMS Intensity)” has
a positive (+) value, a setting of + for this parameter will
allow “AMS” to raise the EG level, and a setting of – will
allow “AMS” to lower the EG level. With a setting of 0 there
will be no change.
B (AMS SW Break)
[–, 0, +]
Specifies the direction in which “AMS (Level Mod. AMS)”
will affect “B (Break Point Level).” When “I (AMS Inten-
sity)” has a positive (+) value, a setting of + for this parame-
ter will allow “AMS” to raise the EG level, and a setting of –
will allow “AMS” to lower the EG level. With a setting of 0
there will be no change.
4.1–5c: Time Mod. (Time Modulation)
These settings let you use alternate modulation to control
the “T (Time)” parameters of the filter 1 EG.
AMS1 (Time Mod. AMS1)
[Off, (KT, EXT)]
Indicates the source that will control the “T (Time)” parame-
ters of the filter 1 EG (
p.222 “AMS List”).
I (AMS1 Intensity)
[–99…+99]
Specifies the depth and direction of the effect that “AMS1
(Time Mod. AMS1)” will have.
For example, if “AMS1 (Time Mod. AMS1)” is set to Flt KTr
+/+
, the EG “T (Time)” parameters will be controlled by the
Keyboard Track (4.1–2a) settings. With positive (+) values of
this parameter, positive (+) values of “Ramp (Ramp Set-
ting)” (4.1–2a) will lengthen the EG times, and negative (–)
values
of “Ramp (Ramp Setting)” will shorten the EG times.
The direction of change is specified by “A (AMS1 SW
Attack),” “D (AMS1 SW Decay),” “S (AMS1 SW Slope),” and
“R (AMS1 SW Release).”
With a setting of 0, the times specified by “Filter1 EG” (4.1–
5a) will be used.
If “AMS1 (Time Mod. AMS1)” is set to Velocity, positive (+)
values
of this parameter will cause EG times to lengthen as
you play more strongly, and negative (–) values will cause
EG times to shorten as you play more strongly.
With a setting of 0, the times specified by “Filter1 EG” will
be used.
A (AMS1 SW Attack)
[–, 0, +]
Specifies the direction in which “AMS1 (Time Mod. AMS1)”
will affect the attack time. With positive (+) values of “I
(AMS1 Intensity),” setting this parameter to + will allow
AMS1 to lengthen the time, and setting this parameter to –
will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
D (AMS1 SW Decay)
[–, 0, +]
Specifies the direction in which “AMS1 (Time Mod. AMS1)”
will affect the decay time. With positive (+) values of “I
(AMS1 Intensity),” setting this parameter to + will allow
AMS1 to lengthen the time, and setting this parameter to –
will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
S (AMS1 SW Slope)
[–, 0, +]
Specifies the direction in which “AMS1 (Time Mod. AMS1)”
will affect the slope time. With positive (+) values of “I
(AMS1 Intensity),” setting this parameter to + will allow
AMS1 to lengthen the time, and setting this parameter to –
will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
R (AMS1 SW Release)
[–, 0, +]
Specifies the direction in which “AMS1 (Time Mod. AMS1)”
will affect the release time. With positive (+) values of “I
(AMS1 Intensity),” setting this parameter to + will allow
AMS1 to lengthen the time, and setting this parameter to –
will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
AMS2 (Time Mod. AMS2)
[Off, (KT, EXT)]
I (AMS2 Intensity)
[–99…+99]
A (AMS2 SW Attack)
[–, 0, +]
D (AMS2 SW Decay)
[–, 0, +]
S (AMS2 SW Slope)
[–, 0, +]
R (AMS2 SW Release)
[–, 0, +]
These parameters are the settings for “AMS2” to control the
“Time” parameters of the filter 1 EG (
☞
“AMS1 (Time Moc.
AMS1)”–“R (AMS1 SW Release)”).
■
4.1–5d: UTILITY
☞
“Write Program” (1.1–1c), “Copy Oscillator,” “Swap
Oscillator” (2.1–1d)
For details on how to select the desired utility function, refer
to “PROG 1.1–1c: UTILITY.”
Filter 1 EG changes (level) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note with “S,”
“A,” and “B” set to + (setting
of 4.1–5a: Filter 1 EG)
Strongly played note with
“S,” “A,” and “B” set to +
Strongly played note with
“S,” “A,” and “B” set to –
Filter 1 EG changes (Time) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note with “A,”
“D,” “S” and “R” set to +
(setting of 4.1–5a: Filter 1 EG)
Strongly played note with
“A,” “D,” “S” and “R” set to +
Strongly played note with
“A,” “D,” “S” and “R” set to –