KORG TRITON STUDIO music workstation - Manual (Page 139)

S.PLA
Y
1.1
2.2
2.3
3.1
4.1
4.2
6.1
6.2
6.3
6.4
7.1
7.2
7.3
129
■ 6.4–4(5)b: UTILITY
☞ “GM Initialize” (1.1–1b)
“Solo Selected Track,” “Set Location” (SEQ 1.1–1d)
“Copy KARMA Module” (PROG 6.1–1c), “Select by Cate-
gory” (PROG 1.1–3b)
“Init KARMA Module” (COMBI 6.1–1d)
6.4–6: Rndm1
(Random 1)
6.4–7: Rndm2
(Random 2)
6.4–6(7)a: Rhythm, Duration, Index, Cluster, Veloc-
ity, CC–A/B, Drum
Rhythm (Rhythm Seed) [1, 2, 3, 4]
Duration (Duration Seed) [1, 2, 3, 4]
Index (Index Seed) [1, 2, 3, 4]
Cluster (Cluster Seed) [1, 2, 3, 4]
Velocity (Velocity Seed) [1, 2, 3, 4]
CC–A/B (CC–A/B Seed) [1, 2, 3, 4]
Drum (Drum Seed) [1, 2, 3, 4]
☞ p.64 COMBI 6.4–6a/7a: Rndm 1/2
■ 6.4–6(7)b: UTILITY
☞ “GM Initialize” (1.1–1b)
“Solo Selected Track,” “Set Location” (SEQ 1.1–1d)
“Copy KARMA Module” (PROG 6.1–1c), “Select by Cate-
gory” (PROG 1.1–3b)
“Init KARMA Module” (COMBI 6.1–1d)
Specifies the bus to which the program oscillator(s) of each
track 1–8, 9–16 will be sent. You can also set the amount of
signal that will be sent to the master effects.
☞ For details on insert effects, refer to “7. Effect Guide”
p.159.
7.1–1: BUS..8
(BUS T01...08)
7.1–2: BUS..16
(BUS T09...16)
7.1–1(2)a: BUS Select, Send1(MFX1), Send2(MFX2)
BUS Select [DKit, L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
Specifies the output bus for the program oscillators of tracks
1–8 and 9–16.
The state of the settings can be viewed in the Route page.
(
☞ COMBI 7.1–1a)
S1 (Send1(MFX1)) [000...127]
S2 (Send2(MFX2)) [000...127]
Here you can adjust the send levels from tracks 1–8, 9–16 to
master effects 1 and 2. This is valid when “BUS Select” is set
either to L/R or Off. If IFX 1, 2, 3, 4, or 5 is selected, the send
level to the master effects 1 and 2 is set by the “S1
(Send1(MFX1))” and “S2 (Send2(MFX2))” parameters
located in the 7.2: Insert FXl, Setup page, after the signal
passes through IFX 1–5.
These settings have no effect if “BUS Select” is set to 1, 2, or
1/2
.
The send 1 and 2 settings you make here will be used when
the SMF is played back from the beginning. You can also
modify the settings during playback. However if the SMF
contains send 1 or 2 data, the settings will change accord-
ingly.
If “Status” 3.1–1(2)a) is INT or BTH, MIDI control
change (CC) #93 or #91 can be received to control send 1
or 2 and change the setting. Tracks 1–16 will be con-
trolled by this data on MIDI channels 1–16 respectively.
The actual send levels are determined by multiplying
the value of these settings with the send level settings
“S1 (Send 1 (MFX1))” and “S2 (Send 2 (MFX2))” (Pro-
gram 7.2–1a) of each oscillator of the program used by
the track.
6.4–6b
6.4–6a
6.4–7b
6.4–7a
S.PLAY 7.1: BUS
7.1–1a
7.1–1b