KORG TRITON STUDIO music workstation - Manual (Page 24)

14
3.1–5b: Level Mod. (Level Modulation)
These settings allow the pitch EG “L (Level)” parameters to
be controlled by alternate modulation.
AMS1 (Level Mod. AMS1) [Off, (KT, EXT)]
Selects the source that will control the pitch EG “L (Level)”
parameters (
☞ p.222 “AMS List”).
I (AMS1 Intensity) [–99…+99]
Specifies the depth and direction of the effect applied by
“AMS1 (Level Mod. AMS1).”
With a setting of 0, the levels specified by “Pitch EG” (3.1–
5a) will be used.
For example, if “AMS1 (Level Mod. AMS1)” is SW1 #80,
pressing the [SW1] key to turn it on will change the “Level”
parameters of the Pitch EG. (“SW1/2 Assign”: 2.2–1b) to
SW1 Mod. (CC#80)
. As the absolute value of “I (AMS1
Intensity)” is increased, the pitch EG levels will change more
greatly when the [SW1] key is turned on. The direction of
the change is specified by “S (AMS1 SW Start)” and “A
(AMS1 SW Attack).” When the [SW1] key is turned off, the
pitch EG levels will return to their own settings.
If “AMS1” is set to Velocity, increasing the absolute value of
“Intensity” will produce increasingly wider change in pitch
EG levels for strongly-played notes. The direction of the
change is specified by “S (AMS1 SW Start)” and “A (AMS1
SW Attack).” As you play more softly, the pitch change will
draw closer to the pitch EG levels.
S (AMS1 SW Start) [–, 0, +]
Specifies the direction of change in “S (Start Level)” caused
by “AMS1 (Level Mod. AMS1).” If “I (AMS1 Intensity)” is a
positive (+)
value, a setting of + will raise the EG level, and
a setting of – will decrease it. With a setting of 0 there will be
no change.
A (AMS1 SW Attack) [–, 0, +]
Specifies the direction of change in “A (Attack Level)”
caused by “AMS1 (Level Mod. AMS1).” If “I (AMS1 Inten-
sity)” is a positive (+) value, a setting of + will raise the EG
level, and a setting of – will decrease it. With a setting of 0
there will be no change.
AMS2 (Level Mod. AMS2) [Off, (KT, EXT)]
I (AMS2 Intensity) [–99…+99]
S (AMS2 SW Start) [–, 0, +]
A (AMS2 SW Attack) [–, 0, +]
Refer to the preceding paragraphs “AMS1 (Level Mod.
AMS1)”–“A (AMS1 SW Attack).”
3.1–5c: Time Mod. (Time Modulation)
These parameters let you use alternate modulation to con-
trol the “T (Time)” parameters of the pitch EG.
AMS (Time Mod. AMS) [Off, (KT, EXT)]
Indicates the source that will control the “T (Time)” parame-
ters of the pitch EG (
☞ p.222 “AMS List”).
I (AMS Intensity) [–99…+99]
Specifies the depth and direction of the effect that “AMS
(Time Mod. AMS)” will have.
With a setting of 0, the pitch EG times will be just as speci-
fied by the “Pitch EG” (3.1–5a) settings.
The alternate modulation value at the moment that the EG
reaches each point will determine the actual value of the EG
time that comes next.
For example, the decay time will be determined by the alter-
nate modulation value at the moment that the attack level is
reached.
When this parameter is set to values of 16, 33, 49, 66, 82, or
99
, the specified EG times will speed up as much as 2, 4, 8,
16, 32, or 64 times respectively (or slowed down to 1/2, 1/4,
1/8, 1/16, 1/32, or 1/64 of the original time).
For example if “AMS (Time Mod. AMS)” is set to Velocity,
increasing the absolute value of “I (AMS Intensity)” will
allow strongly-played notes to increase the changes in pitch
EG “T (Time)” values. The direction of the change is speci-
fied by “A (AMS SW Attack)” and “D (AMS SW Decay).” As
you play more softly, the pitch EG times will more closely
approach the actual settings of the pitch EG.
A (AMS SW Attack) [–, 0, +]
Specifies the direction in which “AMS (Time Mod. AMS)”
will affect the “A (Attack Time).” With positive (+) values of
“I (AMS Intensity),” a setting of + will cause the time to be
lengthened, and a setting of – will cause the time to be short-
ened. With a setting of 0 there will be no change.
D (AMS SW Decay) [–, 0, +]
Specifies the direction in which “AMS (Time Mod. AMS)”
will affect the “D (Decay Time).” With positive (+) values of
“I (AMS Intensity),” a setting of + will cause the time to be
lengthened, and a setting of – will cause the time to be short-
ened. With a setting of 0 there will be no change.
■ 3.1–5d: UTILITY
☞ “Write Program” (1.1–1c), “Copy Oscillator,” “Swap
Oscillator” (2.1–1d)
Pitch EG change (level) (AMS=SW1/Velocity, Intensity= positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with “S”
set at 0, “A” set to +, and
SW1 turned on (the settings
of 3.1–5a: Pitch EG) A note played strongly with
“S” set to 0, “A” set to +, and
SW1 turned on A note played strongly with
“S” set to 0, “A” set to –, and
SW1 turned on
Pitch EG changes (Time) (AMS = Velocity, Intensity = positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with “A”
set to + and “D” set to +
(settings of 3.1–5a: Pitch EG) A note played strongly with
“A” set to + and “D” set to + A note played strongly with
“A” set to – and “D” set to –