KORG TRITON STUDIO music workstation - Manual (Page 172)

162
For example, if the snare-type sounds are set to IFX1 and the
kick-type sounds are set to IFX2, and you wish to use differ-
ent effects than timbres 2 and 3 as the drum program effects,
you can use “DrumKit IFX Patch.” Select “DKit IFX Patch”
from the Utility, and temporarily send the drum kit IFX1 to
IFX3 and IFX2 to IFX4. When you execute the command,
snare sounds will be sent to IFX3 and kick sounds to IFX4 so
that these effects can be applied.
DrumKit IFX Patch dialog
After setting the parameters
3. Mixer
For each mode, use 7.2: Ed-InsertFX (or Insert FX) Setup
page parameters “Pan (CC#8),” “BUS Select,”“S1 (Send 1
(MFX1)),” and “S2 (Send 2 (MFX2))” to specify the pan, bus
select, and the send levels to master effects MFX1 and MFX2
for the signals that have passed through the insert effects. If
you have set “Chain” to
to connect insert effects in series,
the parameters listed above will be applied after the signal
has passed through the last insert effect.
3–1. Pan (CC#8)
Specifies the pan after passing through the insert effect.
If the insert effect is a Stereo In–Stereo Out type (
☞ ”In/
Out”), setting this parameter to C064 will allow the “Pan”
settings of the oscillator (PROG 5.1–1, PROG 5.2–1), timbre
(COMBI 1.1–3, 2.1–2), track (SEQ 1.1–4/5, S.PLAY 1.1–4/5)
to be used.
If the insert effect is a Mono In-Stereo Out or Mono In-
Mono Out
type ( ☞ “In/Out”), the “Pan” of the oscillator,
timbre, track, or audio input (see above) will be ignored, and
the sound will always be panned to the center. In this case,
the “Pan (CC#8)” (7.2–1) that follows the insert effect will
determine the final panning. L001 is far left and R127 is far
right.
You can control these parameters via MIDI Control
Change CC#8.
3–2. BUS Select
This parameter enables you to specify the destination bus
for the post-IFX signals.
“L/R” is a common setting to send signals to the Master EQ
before they are routed to the OUTPUT L/R outputs.
Select 1, 2 or 1/2 to route the signals to AUDIO OUTPUT
(INDIVIDUAL) 1 or2 (
☞ “Individual Output”). Select “Off”
so that no signals will be output to L/MONO, R, 1 or 2. In
this case, the signals are routed from the Master Effects to
AUDIO OUTPUT (MAIN). This setting is used when you
are connecting the Insert Effects with the Master Effects in
series using “S1 (Send1(MFX1))” and S2 (Send2(MFX2)).”
3–3. Send level
These parameters enable you to set the send level of the sig-
nals routed to Master Effects MFX1 and MFX2. These set-
tings are effective only when “BUS Select” is set to L/R or
Off
.
If you are not using insert effects, set the PROG 7.1–1 MFX
Send “Send 1” and “Send 2” parameters, the COMBI 7.1–1
“S1 (Send 1 (MFX1))” and “S2 (Send 2 (MFX2))” parameters,
the Sequencer mode SEQ 7.1–1/2, “S1 (Send1 (MFX1))”
and “S2 (Send2 (MFX2))” parameters, or the Song Play
mode S.PLAY 7.1–1/2 “S1 (Send1 (MFX1)) and “S2 (Send2
(MFX2))” to set the send levels to master effects MFX1 and
MFX2.
Send Level 1 can be controlled by MIDI Control Change
CC#93 and Send Level 2 can be controlled by MIDI
Control Change CC#91
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left Center Right
Post IFX Pan(CC#8)
C064
Left Center Right
L032
L000
R096
R127
Insert Effect = Stereo In - Stereo Out
Left Center Right
Left Center Right
OSC1 OSC2
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Post IFX Pan(CC#8)
C064
L032
L000
R096
R127
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left Center Right
Post IFX Pan(CC#8)
C064
Left Center Right
L032
L000
R096
R127
Insert Effect = Mono In - Stereo Out
OSC1 OSC2
Mono In - Mono Out