Rockwell Automation 1783-WAPxxx Stratix 5100 Wireless Access Point User Manual - Manual (Page 584)

584 Rockwell Automation Publication 1783-UM006A-EN-P - May 2014
Appendix C Error and Event Messages
System Log Messages This table explains the system log messages.
802.11 Subsystem Messages This table explains the subsystem messages.
Table 5 - System Log Messages
Message Explanation Recommended Action
%DOT11-4-LOADING_RADIO: Interface [chars],
loading the radio firmware ([chars])
The radio has been stopped to load new
firmware. No action is required.
%LINEPROTO-5-UPDOWN: Line protocol on Interface
[chars], changed state to [chars]
The data link level line protocol has
changed state. No action is required.
%SYS-5-RESTART: System restarted --[chars] A reload or restart was requested. Notification message only. No action is required.
%SYS-5-CONFIG_I: Configured from [chars] by
[chars]
The router configuration has been
changed. This is a notification message only. No action is
required.
%LINEPROTO-5-UPDOWN: Line protocol on Interface
[chars], changed state to [chars]
The data link level line protocol has
changed state on the interface shown. No action is required.
%SNMP-5-COLDSTART: SNMP agent on host [chars] is
undergoing a cold start
The SNMP server completed a coldstart. Notification message only. No action is required.
%SYS-6-CLOCKUPDATE: System clock has been updated
from [chars] to [chars], configured from [chars]
by [chars].
The system clock has been modified. This is an informational message only. No action
is required.
Table 6 - Subsystem Messages
Message Explanation Recommended Action
DOT11-6-FREQ_USED: “Interface %s,
frequency %d selected.”
After scanning for an unused frequency, the indicated
interface selected the displayed frequency. None.
DOT11-4-NO-VALID_INFRA_SSID: “No
infrastructure SSID configured. %s not
started.”
No infrastructure SSID was configured and the indicated
interface was not started. Add at least one infrastructure SSID to the
radio configuration.
DOT11-4-VERSION_UPGRADE: “Interface %d,
upgrading radio firmware.”
When starting the indicated interface, the access point
found the wrong firmware version. The radio is loaded
with the required version. None.
DOT11-2-VERSION_INVALID: “Interface %d,
unable to find required radio version
%x.%x/ %d/
When trying to upgrade the radio firmware on the
indicated interface, the access point recognized that the
indicated radio firmware packaged with the Cisco IOS
software had the incorrect version. None.
DOT11-3-RADIO_OVER_TEMPERATURE:
“Interface %s Radio over temperature
detected.”
The radio’s internal temperature exceeds maximum limits
on the indicated radio interface. Take steps necessary to reduce the internal
temperature. These steps vary based on your
specific installation.
DOT11-6-RADIO_TEMPERATURE_NORMAL:
“Interface %s radio temperature returned
to normal.”
The radio’s internal temperature has returned to normal
limits on the indicated radio interface. None.
DOT11-3-TX_PWR_OUT_OF_RANGE: “Interface
%s Radio transmit power out of range.”
The transmitter power level is outside the normal range
on the indicated radio interface. Remove unit from the network and service.
DOT11-3-RADIO_RF_LO: “Interface %s Radio
cannot lock RF freq.”
The radio phase lock loop (PLL) circuit is unable to lock the
correct frequency on the indicated interface. Remove unit from network and service.
DOT11-3-RADIO_IF_LO: “Interface %s Radio
cannot lock IF freq.”
The radio intermediate frequency (IF) PLL is unable to lock
the correct frequency on the indicated interface. Remove unit from network and service.
DOT11-6-FREQ_SCAN: “Interface %s Scanning
frequencies for %d seconds.”
Starting a scan for a least congested frequency on the
interface indicated for a the time period indicated. None.
DOT11-2-NO_CHAN_AVAIL: “Interface %s, no
channel available.”
No frequency is available, likely because RADAR has been
detected within the previous 30 minutes. None.