Teledyne 9110EH - Nitrogen Oxides Analyzer - Manual (Page 11)

Model 9110EH Instruction Manual M9110EH Documentation
LIST OF TABLES
Table 2-1: Model 9110EH Basic Unit Specifications.......................................................... 5
Table 3-1: Inlet / Outlet Connector Nomenclature .......................................................... 13
Table 3-2: Analog Output Pin-Outs............................................................................... 18
Table 3-3: Status Output Signals ................................................................................. 18
Table 3-4: Control Input Signals .................................................................................. 19
Table 3-5: Front Panel Display During System Warm-Up ................................................. 21
Table 3-6: Possible Warning Messages at Start-Up ......................................................... 23
Table 5-1: IZS or Z/S Valve States .............................................................................. 38
Table 5-2: Available Permeation Source Options ............................................................ 39
Table 5-3: Contents of Zero Air Scrubber Maintenance Kit ............................................... 40
Table 5-4: Dryer and NH
3
Removal Options................................................................... 42
Table 6-1: Analyzer Operating modes........................................................................... 45
Table 6-2: Test Functions Defined................................................................................ 47
Table 6-3: List of Warning Messages Revision C.4 .......................................................... 48
Table 6-4: Password Levels......................................................................................... 49
Table 6-5: Variable Names (VARS) Revision C.4............................................................. 59
Table 6-6: M9110EH Diagnostic (DIAG) Functions.......................................................... 61
Table 6-7: DIAG - Analog I/O Functions........................................................................ 64
Table 6-8: Analog Output Voltage Ranges ..................................................................... 64
Table 6-9: Analog Output Current Loop Range............................................................... 65
Table 6-10: Analog Output Pin Assignments.................................................................... 65
Table 6-11: Voltage Tolerances for Analog Output Calibration............................................ 68
Table 6-12: Current Loop Output Calibration with Resistor ................................................ 72
Table 6-13: Test Parameters Available for Analog Output A4 ............................................. 73
Table 6-14: Status Output Pin Assignments .................................................................... 77
Table 6-15: Control Input Pin Assignments ..................................................................... 78
Table 6-16: COM1 and COM2 DB-9 Pin Assignments ........................................................ 81
Table 6-17: COM Port Communication Modes .................................................................. 82
Table 6-18: Ethernet Status Indicators........................................................................... 85
Table 6-19: Front Panel LED Status Indicators for iDAS .................................................... 89
Table 6-20: iDAS Data Channel Properties ...................................................................... 90
Table 6-21: iDAS Data Parameter Functions.................................................................... 91
Table 6-22: M9110EH Default iDAS Configuration, Revision C.7. ........................................ 93
Table 6-23: Terminal Mode Software Commands ............................................................107
Table 6-24: Command Types .......................................................................................108
Table 6-25: Serial Interface Documents ........................................................................112
Table 7-1: IZS Option Valve States with CAL_ON_NO
2
Turned ON ...................................121
Table 7-2: AutoCal Modes..........................................................................................126
Table 7-3: AutoCal Attribute Setup Parameters.............................................................126
Table 7-4: Example Auto-Cal Sequence .......................................................................127
Table 7-5: Calibration Data Quality Evaluation..............................................................129
Table 8-1: Activity Matrix for EPA Calibration Equipment and Supplies .............................132
Table 8-2: Activity Matrix for Calibration Procedure .......................................................132
Table 8-3: Definition of Level 1 and Level 2 Zero and Span Checks..................................140
Table 8-4: Activity Matrix for Data Quality ...................................................................141
Table 9-1: M9110EH Preventive Maintenance Schedule..................................................145
Table 9-2: Predictive Uses for Test Functions................................................................147
Table 10-1: List of Interferents ....................................................................................164
Table 10-2: M9110EH Valve Cycle Phases......................................................................167
Table 10-3: M9110EH Gas Flow Rates...........................................................................172
Table 10-4: Front Panel Status LED’s ............................................................................188
M9110EH Rev 0 xi