Yaskawa Z1000U - Manual (Page 374)

SCF ............................................................................... 201
S-Curve Characteristics .................................................. 156, 188
SE ................................................................................. 209
Secondary PI Disable Mode................................................... 303
Secondary PI Display Digits .................................................. 302
Secondary PI Enable Selection ............................................... 302
Secondary PI Feedback Detection Selection ................................ 303
Secondary PI High Feedback Detection Time .............................. 303
Secondary PI High Feedback Level .......................................... 303
Secondary PI Integral Limit Setting.......................................... 303
Secondary PI Integral Time Setting .......................................... 303
Secondary PI Low Feedback Detection Level .............................. 303
Secondary PI Low Feedback Detection Time .............................. 303
Secondary PI Output Level Selection ........................................ 303
Secondary PI Output Lower Limit ........................................... 303
Secondary PI Output Upper Limit............................................ 303
Secondary PI Proportional Gain Setting ..................................... 303
Secondary PI Setpoint Value.................................................. 303
Secondary PI Unit Selection .................................................. 302
Secondary PI User Display .............................................. 302, 304
Second Line Monitor Selection ............................................... 174
Selecting the Type of Auto-Tuning .......................................... 134
Selection of Parameter Write during Uv..................................... 299
Self-Diagnostics................................................................. 337
Sequence Timer 1 Day Selection ............................................. 300
Sequence Timer 1 Reference Source......................................... 300
Sequence Timer 1 Selection................................................... 300
Sequence Timer 1 Start Time ................................................. 300
Sequence Timer 1 Stop Time ................................................. 300
Sequence Timer 2 Day Selection ............................................. 301
Sequence Timer 2 Reference Source......................................... 301
Sequence Timer 2 Selection................................................... 301
Sequence Timer 2 Start Time ................................................. 301
Sequence Timer 2 Stop Time ................................................. 301
Sequence Timer 3 Day Selection ............................................. 301
Sequence Timer 3 Reference Source......................................... 301
Sequence Timer 3 Selection................................................... 301
Sequence Timer 3 Start Time ................................................. 301
Sequence Timer 3 Stop Time ................................................. 301
Sequence Timer 4 Day Selection ............................................. 302
Sequence Timer 4 Reference Source......................................... 302
Sequence Timer 4 Selection................................................... 302
Sequence Timer 4 Start Time ................................................. 301
Sequence Timer 4 Stop Time ................................................. 302
Sequence Timer Error .......................................................... 213
SEr ................................................................................ 201
Serial Comms Cable Connection Terminal ................................. 322
Serial Communication Terminals...............................................83
Serial Communication Transmission Error ................................. 204
Set Time.......................................................................... 299
Setup Group ..................................................................... 105
Setup Group Parameters ....................................................... 106
Setup Mode ...................................................................... 102
Shielded Twisted-Pair Cables ...................................................86
Simple Motor Setup Using V/f Control...................................... 109
Simplified Setup Using the Setup Group .................................... 102
Sinking/Sourcing Mode for Digital Inputs ....................................82
SN...................................................................................82
Snubber Discharge Resistor Overheat ....................................... 201
Soft Charge Bypass Relay Maintenance..................................... 314 Soft Charge Bypass Relay Maintenance Time.............................. 208
Soft CLA Selection ............................................................. 293
Soft Starter Speed Reference at Previous Fault............................. 311
Software Current Limit Selection ............................................ 171
Software No. (Flash) ........................................................... 310
Software No. (ROM) ........................................................... 310
Software version ..................................................................27
SoH ............................................................................... 201
Speed Agreement Detection Level ........................................... 291
Speed Agreement Detection Level (+/-)..................................... 291
Speed Agreement Detection Width .......................................... 291
Speed Agreement Detection Width (+/-) .................................... 292
Speed Control Accuracy ....................................................... 246
Speed Control Range ........................................................... 246
Speed Feedback Detection Control Gain .................................... 295
Speed Response ................................................................. 246
Speed Search Deceleration Time ............................................. 147
Speed Search Delay Time ..................................................... 147
Speed Search Detection Compensation Gain ............................... 147
Speed Search Method Selection .............................................. 148
Speed Search Restart Current Level.......................................... 148
Speed Search Restart Detection Time........................................ 148
Speed Search Selection at Start ............................................... 146
Speed Search Wait Time....................................................... 148
SrC................................................................................ 201
Srr ................................................................................. 201
Stall Prevention ................................................................. 188
Stall Prevention Level during Acceleration ................................. 290
Stall Prevention Level during Run ........................................... 291
Stall Prevention Limit during Acceleration ................................. 290
Stall Prevention Selection during Acceleration............................. 290
Stall Prevention Selection during Deceleration............................. 290
Stall Prevention Selection during Run ....................................... 291
Standard .......................................................................... 247
Standard Connection Diagram ..................................................56
Starting Torque.................................................................. 246
Start Speed Search Select...................................................... 148
Start-Up Flowcharts ............................................................ 107
Station Address Setting Error ................................................. 204
Stationary Auto-Tuning........................................................ 133
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 131
STo ............................................................................... 201
STOP Key Function Selection ................................................ 176
Stopping Method after Communication Error ........................ 165, 324
Stopping Method Selection.................................................... 117
Storage Temperature .............................................................42
Supported Properties of Objects .............................................. 330
Surrounding Area .................................................................42
SvE ............................................................................... 202
T
T/L3.................................................................................70
T1-07 ............................................................................. 135
T1 Tuning Start ................................................................. 306
Task Complete .................................................................. 216
TdE ............................................................................... 202
Temperature Derating .......................................................... 250
Terminal A1 Bias Setting...................................................... 125
Terminal A1 Function Selection.............................................. 162
Terminal A1 Gain Setting ..................................................... 125
Index
374 YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual