Yaskawa Z1000U - Manual (Page 373)

PID Offset Adjustment......................................................... 149
PID Output....................................................................... 315
PID Output 2 Monitor Max Upper/Lower 4 Digits ........................ 155
PID Output 2 Monitor Minimum ............................................. 155
PID Output Gain Setting....................................................... 150
PID Output Level Selection ................................................... 149
PID Output Limit ............................................................... 149
PID Output Lower Limit....................................................... 153
PID Output Monitor Calculation Method ................................... 155
PID Output Reverse Selection ................................................ 150
PID Output Reverse Selection 2 .............................................. 156
PID Primary Delay Time Constant ........................................... 149
PID Setpoint ..................................................................... 315
PID Setpoint Boost Setting .................................................... 152
PID Setpoint Display Digits................................................... 154
PID Setpoint Monitor Unit Selection ........................................ 155
PID Setpoint Scaling ........................................................... 152
PID Setpoint Selection ......................................................... 151
PID Setpoint User Display .................................................... 154
PID Setpoint Value ............................................................. 151
PID Sleep Delay Time ......................................................... 151
PID Sleep Function Start Level ............................................... 151
PID Sleep Input Source ........................................................ 152
PID Snooze Deactivation Level .............................................. 152
PID Snooze Delay Time ....................................................... 152
PID Snooze Feedback Level .................................................. 153
PID Snooze Level............................................................... 152
PID Square Root Gain ......................................................... 153
PID Unit Selection.............................................................. 154
PI Feedback Loss ......................................................... 196, 207
PM Motor Auto-Tuning Mode Selection .................................... 137
PM Motor Base Frequency .................................................... 137
PM Motor Code................................................................. 123
PM Motor Code Selection ..................................................... 137
PM Motor d-Axis Inductance ................................................. 138
PM Motor Induced Voltage Constant ........................................ 138
PM Motor Parameter Settings................................................. 132
PM Motor q-Axis Inductance ................................................. 138
PM Motor Rated Current ...................................................... 137
PM Motor Rated Power........................................................ 137
PM Motor Rated Voltage ...................................................... 137
PM Motor Stator Resistance .................................................. 138
PM Motor Type ................................................................. 137
PM Rotational Auto-Tuning................................................... 132
PM Stationary Auto-Tuning................................................... 132
PM Stationary Auto-Tuning for Stator Resistance ......................... 132
Power Consumption Output Unit Selection................................. 124
Powering Up the Drive......................................................... 111
Power Ratings (Three-Phase 200 V Class)............................ 242, 243
Power Ratings (Three-Phase 400 V Class)............................ 244, 245
Power Supply Frequency Fault ............................................... 196
Power Supply Overvoltage .................................................... 193
Power Supply Undervoltage................................................... 193
Predefined V/f Patterns ........................................................ 159
Preparing the Ends of Shielded Cables ........................................86
Present Value Access........................................................... 330
Previous Fault ................................................................... 311
Programming Errors............................................................ 211
Programming Mode ...................................................... 100, 102
Proportional Gain Setting (P) ................................................. 149 Pull-In Current .................................................................. 295
Pull-In Current Compensation Time Constant.............................. 295
Pull-In Current during Accel/Decel for PM................................. 202
Pull-In Current Level for PM Motor Tuning................................ 138
Pump (Secondary) Application ............................................... 114
Pump with PI Control Application .......................................... 114
R
R-....................................................................................83
R/L1 ................................................................................70
R+...................................................................................83
Rated Current Depending on Carrier Frequency .............................18
Rated Current Setting Alarm .................................................. 214
Rated Slip Error ................................................................. 215
rdEr ............................................................................... 217
READ ............................................................................ 177
rEAd .............................................................................. 217
Reading BACnet Drive Parameters .......................................... 335
Reading Parameter Settings ................................................... 217
Real Time Clock Setting....................................................... 179
Reattaching the Front Cover ....................................................68
Reattaching the HOA Keypad ..................................................66
Reattaching the Terminal Cover ................................................63
Removing the Front Cover ......................................................66
Removing the HOA Keypad ....................................................66
Removing the Protective Cover.................................................69
Removing the Terminal Cover..................................................63
RESET Key........................................................................95
Resistance Tuning Error ....................................................... 214
Response Messages from Drive to Master .................................. 329
Return Fan with PI Control Application..................................... 113
Reverse Operation Selection .................................................. 145
Rotational Auto-Tuning for V/f Control Energy Saving .................. 131
RS-485 Interface ................................................................ 323
RTS Control Selection ................................................... 166, 325
Run Command/Frequency Reference Source Selection Error............ 212
Run Command at Power Up................................................... 145
Run Command Method Selection ...................................... 167, 326
Run Command Selection ...................................................... 221
RUN Command Selection for AUTO mode ................................ 256
Run Command Selection for AUTO Mode ................................. 116
Run Command Source Selection ............................................. 315
S
S- ....................................................................................83
S: Special Parameters .......................................................... 300
S/L2.................................................................................70
S+ ...................................................................................83
S1 ...................................................................................82
S1: Dynamic Noise Control Function........................................ 300
S2 ...................................................................................82
S2: Sequence Timers ........................................................... 300
S3 ...................................................................................82
S4 ...................................................................................82
S5 ...................................................................................82
S6 ...................................................................................82
S7 ...................................................................................82
S8 ...................................................................................82
Safety Circuit Fault ............................................................. 201
SC...................................................................................82
Index
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual 373