Yaskawa Z1000U - Manual (Page 363)

No. Name
User
Setting
d7-02
Offset Frequency 2
d7-03
Offset Frequency 3
E1-03 V/f Pattern Selection
E1-04 Maximum Output Frequency
E1-05 Maximum Voltage
E1-06 Base Frequency
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
E1-11 Middle Output Frequency 2
E1-12 Middle Output Frequency Voltage 2
E1-13 Base Voltage
E2-01 Motor Rated Current
E2-02 Motor Rated Slip
E2-03 Motor No-Load Current
E2-04 Number of Motor Poles
E2-05 Motor Line-to-Line Resistance
E2-10 Motor Iron Loss for Torque Compensation
E2-11 Motor Rated Power
E5-01 Motor Code Selection (for PM Motors)
E5-02 Motor Rated Power
E5-03 Motor Rated Current
E5-04 Number of Motor Poles
E5-05 Motor Stator Resistance
E5-06 Motor d-Axis Inductance
E5-07 Motor q-Axis Inductance
E5-09 Motor Induction Voltage Constant 1
E5-24 Motor Induction Voltage Constant 2
H1-01
Multi-Function Digital Input Terminal S1 Function
Selection
H1-02
Multi-Function Digital Input Terminal S2 Function
Selection
H1-03
Multi-Function Digital Input Terminal S3 Function
Selection
H1-04
Multi-Function Digital Input Terminal S4 Function
Selection
H1-05
Multi-Function Digital Input Terminal S5 Function
Selection
H1-06
Multi-Function Digital Input Terminal S6 Function
Selection
H1-07
Multi-Function Digital Input Terminal S7 Function
Selection
H1-08
Multi-Function Digital Input Terminal S8 Function
Selection
H2-01 Multi-Function Contact Output (terminal M1-M2)
H2-02
Multi-Function Contact Output 2 (terminal M3-
M4)
H2-03
Multi-Function Contact Output 3 (terminal MD-
ME-MF)
H3-01 Terminal A1 Signal Level Selection
No. Name
User
Setting
H3-02 Terminal A1 Function Selection
H3-03
Terminal A1 Gain Setting
H3-04
Terminal A1 Bias Setting
H3-05 Terminal A3 Signal Level Selection
H3-06 Terminal A3 Function Selection
H3-07 Terminal A3 Gain Setting
H3-08 Terminal A3 Bias Setting
H3-09 Terminal A2 Signal Level Selection
H3-10 Terminal A2 Function Selection
H3-11
Terminal A2 Gain Setting
H3-12
Terminal A2 Bias Setting
H3-13 Analog Input Filter Time Constant
H3-14 Analog Input Terminal Enable Selection
H3-16 Terminal A1 Offset
H3-17 Terminal A2 Offset
H3-18 Terminal A3 Offset
H4-01
Multi-Function Analog Output Terminal FM
Monitor Selection
H4-02
Multi-Function Analog Output Terminal FM Gain
H4-03
Multi-Function Analog Output Terminal FM Bias
H4-04
Multi-Function Analog Output Terminal AM
Monitor Selection
H4-05
Multi-Function Analog Output Terminal AM Gain
H4-06
Multi-Function Analog Output Terminal AM Bias
H4-07
Multi-Function Analog Output Terminal FM
Signal Level Selection
H4-08
Multi-Function Analog Output Terminal AM
Signal Level Selection
H5-01 Drive Slave Address
H5-02 Communication Speed Selection
H5-03 Communication Parity Selection
H5-04 Stopping Method After Communication Error (CE)
H5-05 Communication Fault Detection Selection
H5-06 Drive Transmit Wait Time
H5-07 RTS Control Selection
H5-08 Communication Protocol Selection
H5-09 CE Detection Time
H5-10
Unit Selection for MEMOBUS/Modbus Register
0025H
H5-11 Communications ENTER Function Selection
H5-12 Run Command Method Selection
H5-14 BACnet Device Object ID
E.3 User Setting Table
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual 363
E
Quick Reference Sheet