Yaskawa Z1000U - Manual (Page 361)

E.3 User Setting Table
Use the Verify Menu to see which parameters have been changed from their original default settings
below the parameter number indicates that the parameter setting can be changed during run.
Parameter names in bold face type are included in the Setup Group of parameters.
No. Name
User
Setting
A1-00
Language Selection
A1-01
Access Level Selection
A1-02 Control Method Selection
A1-03 Initialize Parameters
A1-04 Password
A1-05 Password Setting
A1-06 Application Preset
A2-01 to
A2-32
User Parameters, 1 to 32
A2-33 User Parameter Automatic Selection
b1-01 Frequency Reference Selection 1
b1-02 Run Command Selection 1
b1-03 Stopping Method Selection
b1-04 Reverse Operation Selection
b1-06 Digital Input Reading
b1-08
Run Command Selection while in Programming
Mode
b1-11 Drive Delay Time Setting
b1-14 Phase Order Selection
b1-17 Run Command at Power Up
b1-24 Commercial Power Operation Switching Selection
b1-25
Commercial Power Switching Output Frequency
Coincidence Level
b1-26
Commercial Power Switching Output Frequency
Noncoincidence Level
b2-01
Zero Speed Level (DC Injection Braking Start
Frequency)
b2-02 DC Injection Braking Current
b2-03 DC Injection Braking Time at Start
b2-04 DC Injection Braking Time at Stop
b2-09 Motor Pre-Heat Current 2
b3-01 Speed Search Selection at Start
b3-03 Speed Search Deceleration Time
b3-04 V/f Gain during Speed Search
b3-05 Speed Search Delay Time
b3-06 Output Current 1 during Speed Search
b3-07
Output Current 2 during Speed Search (Speed
Estimation Type)
b3-08
Current Control Gain during Speed Search (Speed
Estimation Type)
b3-09
Current Control Integral Time during Speed Search
(Speed Estimation Type)
b3-10 Speed Search Detection Compensation Gain
No. Name
User
Setting
b3-11
Speed Search Method Switching Level (Speed
Estimation Type)
b3-12
Minimum Current Detection Level during Speed
Search
b3-14 Bi-Directional Speed Search Selection
b3-17 Speed Search Restart Current Level
b3-18 Speed Search Restart Detection Time
b3-19 Number of Speed Search Restarts
b3-24 Speed Search Method Selection
b3-25 Speed Search Wait Time
b3-27 Start Speed Search Select
b3-29 Speed Search Induced Voltage Level
b3-31
Speed Search Operation Current Level 1 (Current
Detection Type 2)
b3-32
Speed Search Operation Current Level 2 (Current
Detection 2)
b3-33
Speed Search Selection when Run Command is
Given during Uv
b3-50 Backspin Search Direction Judgment Time 1
b3-51 Backspin Search Direction Judgment Time 2
b3-52 Backspin Search Deceleration Time 1
b3-53 Backspin Search Deceleration Time 2
b4-01 Timer Function On-Delay Time
b4-02 Timer Function Off-Delay Time
b4-03 H2-01 ON Delay Time
b4-04 H2-01 OFF Delay Time
b4-05 H2-02 ON Delay Time
b4-06 H2-02 OFF Delay Time
b4-07 H2-03 ON Delay Time
b4-08 H2-03 OFF Delay Time
b5-01 PI Function Setting
b5-02
Proportional Gain Setting (P)
b5-03
Integral Time Setting (I)
b5-04
Integral Limit Setting
b5-05
Derivative Time (D)
b5-06
PI Output Limit
b5-07
PI Offset Adjustment
E.3 User Setting Table
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual 361
E
Quick Reference Sheet